Top-rated masons.

Best masons near Clarksville, AR

Enter your zip and get matched with up to 5 pros

Need a pro for your masonry work project in Clarksville, AR?

Select your specific project to find the pro for you.

Top-Rated Masons in Clarksville - Updated Nov 2026

Avatar for Duraplex LLC
Duraplex LLC
4.5(
45
)
Basement Drainage Channels - InstallBasement Drainage Channels - RepairConcrete Foundation - Raise+3 more

Serving Clarksville, AR and surrounding areas

In business since 2006

Free estimates

Emergency services offered

"Very professional, friendly, and prompt service.  They took time to explain what had caused the damages to the roof and what needed to be done to prevent the damages from re-occurring.  Also, they explained the benefits of a full roof replacement vs just repairing the damaged area. 
"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+16

Recommended by91%of homeowners
Andrew's Landscaping and Lawn Maintenance
4.0(
10
)
Brick and Stone Flatwork - RepairBrick and Stone Patios, Walks, and Steps - InstallBrick, Stone or Block Wall - Install+2 more

Serving Clarksville, AR and surrounding areas

In business since 1986

Free estimates

Credit card accepted

"Contacted Tru Cut and they gave me an estimate within 24hrs.  As I requested (hoping more leaves would fall), they waited one week to do the work.  We have a steep driveway with water run-off "ditches" on either side that go behind the garage and down to the lake.  They cleaned the ditches, our driveway/parking pad, and the back yard.  The job was excellent.  Will definitely hire them again.
"
Recommended by100%of homeowners
Showing 1-10 of 34
Masonry FAQs, answered by experts

Limewash can be removed from brick, but the method of removal will depend on how long the limewash has been on the brick. If the limewash has fully dried—which happens after about five days—you’ll need to use a diluted muriatic acid mixture to remove it. If there are multiple coats of limewash, you may need to apply the acid mixture several times to fully remove it from the brick.

To stain brick, you should use a product specifically formulated for brick, concrete, or other masonry surfaces. These stains are designed to penetrate the porous surface of the brick and bond with it. This is different from paint, which sits on the surface and is prone to peeling, flaking, and trapping moisture that can cause damage. Water-based brick stains are often recommended because they are easy to apply, even for DIYers, and they allow the brick to breathe. Avoid using regular paint on brick, as it will not adhere properly and can lead to future maintenance problems.

No, you don’t need to soak the brick before cutting it by hand. In fact, cutting a wet brick can make it harder to see your score lines and may cause the chisel to slip. Soaking is sometimes used with power tools to reduce dust, but for hand-cutting, it’s best to work with dry bricks for better control and visibility.

You can turn a red brick white through a process called whitewashing. Whitewash isn’t a stain but rather is made from water and white latex paint. Adding more water to the mix will make the solution look lighter when applied, and adding more paint will make it look more white.

If you want to make your home eco-friendly, enjoy low maintenance, and love the fact that its looks will take people’s breath away (and not because they were trying to blow your house down), then a modern brick home is right for you. You can hire a mason to get the building process started for your brick home.

But if you’re not fond of the color and don’t want to deal with the process of repointing or other repairs, consider going with vinyl or wood. These materials offer a lower cost. While they tend to require more maintenance, they don’t cost nearly the same as exterior brick house repair.

The Clarksville, AR homeowners’ guide to masonry services

From average costs to expert advice, get all the answers you need to get your job done.