Top-rated well and pump technicians.

Get matched with top well and pump technicians in Hondo, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Hondo, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Hondo, NM

*The Angi rating for Well And Pump Service companies in Hondo, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Hondo, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on September 24, 2022

Find Well and pump technicians in Hondo

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Hondo, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

If you’re going away on vacation or leaving your home for a long time, it’s a good idea to switch off your well pump and pressure tank before you go. This way you can prevent any damage from unexpected leaks that may occur or unforeseen electrical issues while you’re away.

If you have a well-related issue, such as your well water stopping, you should hire a local water well contractor or a well and pump repair professional. These specialists handle all aspects of wells, including the pump, tank, and other outdoor water pumping equipment. They can inspect your system, recommend and perform repairs, and even coordinate a water quality test if needed. While plumbers are experts in indoor plumbing, they may not have the specialized experience with residential wells that a dedicated well contractor does.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

For the most part, choosing between 30/50 psi and 40/60 psi is based on your water-pressure preference. However, it can also depend a little bit on your house—if you have older plumbing, a lower water pressure can be easier on the pipes (and a bit more gentle on your well pump). 

The lower 30/50 pressure is usually enough for a single-story home, but you may want 40/60 if you have multiple stories, as the extra pressure helps water flow smoothly up to the second floor.

The Hondo, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles