Top-rated well and pump technicians.

Get matched with top well and pump technicians in Alto, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Alto, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Alto, NM

*The Angi rating for Well And Pump Service companies in Alto, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Alto, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on November 20, 2025

Find Well and pump technicians in Alto

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Alto, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

If you’re going away on vacation or leaving your home for a long time, it’s a good idea to switch off your well pump and pressure tank before you go. This way you can prevent any damage from unexpected leaks that may occur or unforeseen electrical issues while you’re away.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The average three to four-bedroom home typically uses a well pump rated for 8 to 12 gallons per minute (GPM). To find the most accurate size for your specific needs, a common rule of thumb is to count the number of water fixtures and appliances in your home and aim for that number in GPM. This calculation allows for about one gallon of water per minute per fixture. Because estimating the correct size can be challenging, it's best to have a professional technician make the final determination. A professional can ensure your pump provides sufficient water for your home, especially during peak usage hours.

A sprinkler pump may not turn on because of problems with the power supply or the circuit breaker. It can also stop working if the motor burns out. If it’s not a tripped breaker, a burned-out motor, or another issue with the power, it’s time to call in a sprinkler repair pro to take a closer look.

There are many reasons you may want to extend the depth of an existing well or drill a new, deeper well on your property. A deeper well can tap cleaner water sources—shallow water may contain more contaminants. With a deeper well, you’ll also have an easier time reaching the water table depth (the level at which underground water is found) and can get past tricky soil conditions. 

Plus, if your local building code requires a minimum well depth for safety and environmental standards, you’ll meet the code by digging a deeper well in the first place.

The Alto, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles