Top-rated well and pump technicians.

Get matched with top well and pump technicians in Tatum, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Tatum, NM?

Select your specific project to find the pro for you.

Find Well and pump technicians in Tatum

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Tatum, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Avatar for LoneStar Developers
LoneStar Developers
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Tatum, NM and surrounding areas

Free estimates

Small jobs welcome

Credit card accepted

Need a reliable commercial or Residential construction crew? \n\nLonestar Developers has you covered. \n\nWe specialize in: \n• Framing \n• Plumbing \n• Electrical \n• Drywall \n• Acoustical Ceilings \n• Mud & Tape \n\nQuality work. Honest service. Built the Texas way. 🤘 \n\n📩 Message us today for quotes or project inquiries.

Wells and Pumps questions, answered by experts

If the well pump is more than 10 years old, it's worth contacting a well pump repair pro near you and weighing the cost of repairs against buying a new well pump. Pumps can last a long time with regular maintenance, but if your pump is nearing the 10-year mark and starts needing repairs frequently, it’s time to replace it.

DIY is not recommended due to safety and technical requirements. Hire professionals for accurate diagnosis and repair.

Both can deliver clean water to your taps, but well water and city water carry a few differences. City water is delivered and connected through a main water line, and it travels through a network of underground private and public pipes to service various buildings and structures once it’s been treated.

Well water is derived from dug or drilled wells that source groundwater from the water table. City water is often more expensive than well water, but it eliminates the need for you to test and treat your own well water.

You should have your well inspected once per year. You should also have a well inspection done when you’re buying a house with a private well, when the well cap is opened, when the septic tank is repaired, or when there is flooding.

During your annual visit, a pro will make sure that everything is working correctly and check for certain contaminants, including total coliform. Every other year, they’ll look for things like metals and nitrates, and every five years, they’ll test for pesticides.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The Tatum, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.