Top-rated well and pump technicians.

Get matched with top well and pump technicians in Atoka, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Atoka, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Atoka, NM

*The Angi rating for Well And Pump Service companies in Atoka, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Atoka, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on April 03, 2025

Find Well and pump technicians in Atoka

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Atoka, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

For the most part, choosing between 30/50 psi and 40/60 psi is based on your water-pressure preference. However, it can also depend a little bit on your house—if you have older plumbing, a lower water pressure can be easier on the pipes (and a bit more gentle on your well pump). 

The lower 30/50 pressure is usually enough for a single-story home, but you may want 40/60 if you have multiple stories, as the extra pressure helps water flow smoothly up to the second floor.

Unfortunately, yes. If your well pump continues working when the flow of water is completely blocked, the motor will burn up. The energy has nowhere to go, thanks to the blockage, so it turns inward. The end result? A ruined well pump and a depleted bank account (once you shop for a replacement.) 

Well pump repair might be covered by your homeowner’s insurance, but it’s typically not. If the damage results from a major storm in your area, flooding, a fire, or some other natural catastrophe, then you should consider filing a claim for the damage. However, if the issue is the result of an aging well pump, your policy will very likely not cover the repair cost. In either case, you should hire a well pump professional inspect your well pump, and then use that information to decide whether or not you should file a claim.

Yes, a bigger well pump can increase water pressure—up to a point. If you currently have a well pump of 8 GPM, you might notice a pressure boost when you go up to 10 GPM. However, overshooting significantly (going up to 15 GPM for an 8 GPM home) can strain your well system and result in things like burst pipes that can decrease your water pressure and make for costly repairs.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

The Atoka, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles