Top-rated above ground pool installation pros.

Get matched with top above ground pool installation pros in Pablo, MT

Enter your zip and get matched with up to 5 pros

Need a pro for your above ground pool installation project in Pablo, MT?

Select your specific project to find the pro for you.

Verified Reviews for Above Ground Pool Installation pros in Pablo, MT

*The Angi rating for Above Ground Pool Installation companies in Pablo, MT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Above Ground Pool Installation needs.

*The HomeAdvisor rating for Above Ground Pool Installation companies in Pablo, MT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Above Ground Pool Installation needs.

Last update on December 04, 2025

Find Above ground pool installation pros in Pablo

Avatar for Choice Home Warranty
Choice Home Warranty
4.0(
5,677
)

Serving Pablo, MT and surrounding areas

In business since 2008

Emergency services offered

Credit card accepted

"The tech was very knowledgeable and went above and beyond to satisfy us. Our faucet was broken would not attach to the sink as the copper seal broke to the water lines."
Recommended by81%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)

Serving Pablo, MT and surrounding areas

In business since 1971

Credit card accepted

"One oven doesn't work at all ( my choice, see above), the "working" oven was never calibrated properly so using it is hit or miss. It's time to call American Home Shield to see about replacing the entire unit. I'm waiting to finish other home projects before calling them. I don't know if I'll request Greenway again."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Install Above Ground Pools questions, answered by experts

Losing some water from splashing and evaporation is normal. However, if you notice a rapid drop in the water level or are adding water more frequently than usual, you might have a leak. Other common signs of a pool leak include:

  • Unexplained soft, mushy, or wet spots in the yard.

  • Cracks in the pool's structure or falling tiles.

  • Higher-than-normal water bills.

  • Persistent algae growth or water discoloration.

  • Standing water near the pump, pipes, or other pool equipment.

It’s fair to be concerned about handling pool lights or wiring in a pool filled with water. But fortunately, pool lights and swimming pools are designed to make it easy and safe to replace the lights without needing to drain the water. Instead, you can turn off the electricity to the pool as a safety precaution, unscrew the pool fixture, pull it up and out to the side of the pool, then change the bulb.

Yes, pool pumps use a significant amount of electricity, making them one of the biggest energy consumers in a home. A pool pump can use up to three times as much electricity as a refrigerator. Typically, a residential pool pump consumes about 1 kilowatt-hour (kWh) for every hour it runs. Because pumps often need to run for about eight hours a day to properly filter the water, this can add up to an annual consumption of 3,000 to 5,000 kWh, which can cost between $480 and $800 per year based on average electricity rates.

The amount of electricity your pump uses depends on its size, energy efficiency, and daily run time. To lower your energy consumption, you can choose an energy-efficient or variable-speed pump, ensure it is correctly sized for your pool, and run it only for the minimum time required to keep the water clean.

Once you use a pH decreaser, you can expect the pH to adjust in two to four hours. If you use a strong chemical like muriatic acid, it could take as little as an hour. Either way, it’s best to wait for a full turnover cycle before retesting. You want to make sure the chemical is completely dissolved and evenly distributed or you won’t have a stable pH level.

A swimming pool pump has to have water in it to run properly. If the pump isn’t primed and tries to run when it’s dry, the components will overheat which can cause the pump to seize up and can even damage the PVC pipes that carry the water into and out of it. Essentially, running a pump that isn’t primed can lead to having to replace the entire pump.

The Pablo, MT homeowners’ guide to above ground pool installation services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles