Top-rated structural engineers.

Get matched with top structural engineers in Medway, OH

Enter your zip and get matched with up to 5 pros

Need a pro for your structural engineering project in Medway, OH?

Select your specific project to find the pro for you.

Find Structural engineers in Medway

Avatar for The Residential Engineer.com
The Residential Engineer.com
5.0(
38
)

Serving Medway, OH and surrounding areas

Approved

In business since 2018

Free estimates

Emergency services offered

"We are builders and have been building in central Ohio for over 25 years. We are thankful to have known Dave. He is extremely knowledgeable, communicates detals in an easy way and is very prompt to deliver. He often finds other ways to engineer things that we hadnt considered which make him our 1st choice in engineers. We would highly reccommend him and his services."
After.
Exterior
Before
Exterior
Sketch for the HOA

+34

Response time6 hrs
Response rate96%
Recommended by96%of homeowners
Avatar for Betts Structural Engineering LLC
Betts Structural Engineering LLC
4.5(
26
)

Serving Medway, OH and surrounding areas

Approved

In business since 2013

Free estimates

Emergency services offered

"Had Betts Structural Engineering come and look at the foundation of a house we were in contract on. Josh came out and was professional and informative. He informed us the foundation was failing and explained what needed to be done. He throughly explained everything and told us how we could do it ourselves for much cheaper than a contractor could do it. In the end he saved us from a long and expensive process if we proceeded with the house."
Response time12 hrs
5 neighbors recently requested a quote
Recommended by100%of homeowners
Avatar for American Basement Solutions
American Basement Solutions
4.3(
46
)

Serving Medway, OH and surrounding areas

In business since 1992

Credit card accepted

"The person who came out and gave an estimate for the work was very accurate in his measurements and was very courteous. They gave us the lowest quote, so we called a couple of weeks later to set up the time for them to work on it. They came to do the work at the scheduled time. They explained what they would be doing and when they were done showed the work to me. There must have been some lack of communication somewhere because the crew that came to do the work didn't know they would have to be tearing out a couple of walls to get the trench dug out. They did it anyway and everything was installed and working great so far, though we haven't had a rainfall yet. The only complaint that we have is that they left a lot to clean up, but I think that was partly because they hadn't planned on cutting out a couple of walls. The price was so low though that if they had planned on that I think the estimate would have been a lot higher. So for that price, we could do the cleanup without too much complaining. This is a company we would definitely hire again.
"
Additional Photos
Additional Photos
Additional Photos
Recommended by85%of homeowners
Structural Engineering questions, answered by experts

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

First, most contractors will have a structural engineer create a report and plan for your project to ensure it’s safe to cut into the load-bearing wall. The contractor will then excavate around the wall, if necessary, measure the opening—allowing for additional space to fit and level the door, and then cut the doorway out. They will likely install a steel lintel as a header over the door for support. Once the doorway is cut out, they’ll demolish the concrete using sledge hammers and masonry chisels, clean up the surrounding concrete, and seal around the door with masonry mortar. 

The essential difference between an architect and an engineer is that architects typically focus more on the aesthetic design of buildings, although not without consideration for the structural integrity of the building. Engineers focus more on the structural, technical, and practical aspects of whether and how an architectural design can be built as drawn. You may need to hire both types of professionals if you’re designing and building a new home.

The process involves initial consultation, concept development, detailed planning, regulatory approvals, and integration of contractor work for project execution.

The average cost to hire a structural engineer is about $550, with prices generally ranging from $200 to $1,500. Structural engineers may charge a flat rate, by the project, by square footage, or an hourly rate, which is typically between $100 and $250. Many jobs, such as inspections and structural calculations, are billed at a flat rate, which often falls between $300 and $800. The final cost depends on several factors, including the project's type, scope, size, complexity, ease of access for inspection, and your geographic location.

The Medway, OH homeowners’ guide to structural engineering services

From average costs to expert advice, get all the answers you need to get your job done.

What do you need done? We’ll find top pros.
  • 🌱 "Mow a small front yard"
  • 🛠 "Fix a leaking pipe under the sink"
  • 🏠 "Repair shingles on an asphalt roof"