Top-rated plumbers.

Get matched with top plumbers in Midway, LA

Enter your zip and get matched with up to 5 pros

Need a pro for your plumbing project in Midway, LA?

Select your specific project to find the pro for you.

TRUSTED BY MIDWAY, LA HOMEOWNERS

  • Average homeowner rating star icon4.1
    Average homeowner rating
  • Verified reviews icon20
    Verified plumbing services reviews

Find Plumbers in Midway

Avatar for FlowPro Plumbing LLC
FlowPro Plumbing LLC
4.5(
15
)
Faucets, Fixtures and Pipes - Repair or ReplaceWater Heater - Repair or ServiceWater Heater - Install or Replace+4 more

Serving Midway, LA and surrounding areas

Approved

In business since 2019

Free estimates

Credit card accepted

"Cody with FlowPro Plumbing did an excellent job in replacing two toilets in our home in Sunset, La. He removed the old toilets and took them away without leaving a mess. While here he also cleared a water line to the bathtub that was clogged with rust. Cody and his helper were very professional, and I would not hesitate to recommend his services."
Finished bathroom
Demo work
20 neighbors recently requested a quote
Recommended by78%of homeowners
Avatar for Neli Virtual Appliance Repair
Neli Virtual Appliance Repair
4.2(
669
)
Refrigeration System - Install or ReplaceRefrigeration System - Install or Replace - For BusinessRefrigeration System - Repair or Service+1 more

Serving Midway, LA and surrounding areas

Approved

In business since 2016

Free estimates

Warranties offered

"I hired Neli over a week period for 3 different appliances, my dryer, washing machine, dishwasher, and even kitchen sink! I had a fantastic experience: 1. I fixed my dryer with Thomas' excellent remote guidance, changing the timer and the switch! Fabulous guidance Thomas, with lots of money saved! I learned a lot in the process. 2. I determined that there was no dishwasher leak and in the process learned how to check for leaks and trouble shoot for some common repair issues. It cost $40.00 but as I had some water on the floor, I was ready to get a new dishwasher. Now, I am confident that it wasn't a leak and caused by putting in the dishes in a funny manner and not a repair issue. I am using the dishwasher now again with no problem. 3. I determined with Thomas' help that the washing machine had a major problem and could have spun out of control into my wall....no question, it was time to get a new washing machine! This was a well spent $40.00--I even got Thomas advice on purchasing a new washing machine and what to look for. 4. I checked the drainage on my kitchen sink and learned how to empty out the "trap" and that most likely, I am okay, but what to swap out if I have continuing issues with slow drainage. In the end, I saved lots of money, gaining and learning valuable experience! Absolutely fabulous service!"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Response time1 day
Recommended by87%of homeowners
Jason Bullock
New to Angi
Drain Clog or Blockage - ClearBathtub Install or ReplaceFaucets, Fixtures and Pipes - Repair or Replace+10 more

Serving Midway, LA and surrounding areas

Approved

Emergency services offered

Small jobs welcome

Credit card accepted

My name's Jason, i do a lot of repairs, i can do installs as well to a limit of permits of course but I will provide as much service I can and get the job done right! I also do some mechanic work as well, Just tell me what you need installed or repaired and I'll guarantee be of help!

Water heater installation
2 neighbors recently requested a quote
...
Showing 1-10 of 77
Plumbing questions, answered by experts

In the best-case scenario, the pipe size is written on the side of the pipe. You’ll often find this with different types of plastic piping like PVC, PEX, or CPVC. For other types of pipes, you’ll have to measure. You can measure the outside circumference with a soft tape measure, then divide your measurement by pi. From there, you’ll have to use a conversion chart to get the nominal pipe size (the size you’d buy in the store).

Yes, you can fit a vanity unit to an existing sink, especially if you plan to custom-build the vanity. With a prefabricated vanity, you’ll likely need to make a few adjustments. It depends on the type of sink, the size of the sink, and the existing plumbing. If you plan to retrofit a sink into a prefabricated vanity, make sure you take precise measurements and that your sink is compatible with the vanity you select. Prefabricated units have a precut sink hole, so you’ll need the size to match your sink.

You can find out what type of shower valve you have by checking the manufacturer’s name and the valve’s serial number or model number. That information should be located on the back of the shower trim. You can use the name and number to do a quick online search to figure out which type of shower valve you have.

Yes. You can replace just the stopper portion with a universal sink stopper. All you need to do is open up the existing stopper and pull it up from the drain. You should be able to remove and replace the stopper with bare hands. If the existing stopper seems to be stuck, use a pair of pliers to remove it.

You may not be able to prevent water spots on your black faucet, but the good news is that you can quickly wipe away water spots, fingerprints, smudges, and smears with a damp cloth. The best practice is to get in the habit of wiping the black faucet daily to prevent any mineral buildup or hard water stains.

The Midway, LA homeowners’ guide to plumbing services

From average costs to expert advice, get all the answers you need to get your job done.