Top-rated contractors.

Get matched with top contractors in Downey, ID

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Downey, ID?

Select your specific project to find the pro for you.

Find Contractors in Downey

Avatar for Jeffreys Painting
Jeffreys Painting
5.0(
11
)

Serving Downey, ID and surrounding areas

In business since 2023

Free estimates

"Jeff was amazing. Jeff was able to not only exceed my expectations in quality and efficiency but made the work exciting. His upbeat personality made the process painless. I would definitely use Jeff again in a heartbeat."
After
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+1

Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)

Serving Downey, ID and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)

Serving Downey, ID and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for Snook Building Company
Snook Building Company
5.0(
3
)

Serving Downey, ID and surrounding areas

In business since 2019

Free estimates

Emergency services offered

"Outstanding experience from start to finish. Dalton is always very available. He treats you like family and everyone performs excellent work. We are loving our new deck! It's sturdy and looks great."
Hart
Smith Basement
Hart
Smith Basement
Hart

+17

Recommended by33%of homeowners
Frontier Mill & Construction, LLC
5.0(
2
)

Serving Downey, ID and surrounding areas

In business since 2004

Free estimates

Emergency services offered

"Excellent service & response. Did not just install carpets; renovated entire home. Wall repair, painting, carpet installation, linoleum installation, caulking, powerwashing, co-ordinating countertop relacement, ceiling fan installation, deck reconstruction and more. An excellent company to work with. Actually, 6 star rating in my opinion. -Jack."
Recommended by100%of homeowners
Showing 1-10 of 23
Unfinished Carpentry questions, answered by experts

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

To calculate the number of linear feet of baseboard you’ll need, measure the length of each wall of the room you’re installing them in as close to the floor as possible, rounding up to the next full linear foot. If it’s your first DIY molding job, having a few extra feet on hand for miscuts is a good idea.

No rules state how much of a load-bearing wall can be removed. Rather, you need to adequately support any area that is removed. Support should always be added to as much wall area is being removed. Failing to support the area properly will result in structural damage.

Framing a house with steel generally takes less time—around five to eight weeks—than most building materials. The steel components can also be made quickly off-site and manufactured with pre-punched holes for running piping and electrical wiring, which will lessen the prep work and extra labor during construction.

Yes, walls on the top floor can be load-bearing if stacked on the floor’s foundation.

The Downey, ID homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.