Top-rated contractors.

Get matched with top contractors in Mccammon, ID

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Mccammon, ID?

Select your specific project to find the pro for you.

Find Contractors in Mccammon

Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Mccammon, ID and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Mccammon, ID and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for Snook Building Company
Snook Building Company
5.0(
3
)
Major Home Repairs (General Contractor)

Serving Mccammon, ID and surrounding areas

In business since 2019

Free estimates

Emergency services offered

"I couldn’t be more thrilled with the deck built by the Snooks! From start to finish, the team was professional, friendly, and focused on delivering top-notch quality. They listened carefully to what we wanted and went above and beyond to make sure every detail was perfect. The craftsmanship is exceptional, and it’s clear they take pride in their work. Not only do they build great decks, but they’re also just genuinely good people to work with. If you’re looking for a company that cares about quality and customer satisfaction, look no further!"
Hart
Smith Basement
Hart
Smith Basement
Hart

+17

Recommended by33%of homeowners
Frontier Mill & Construction, LLC
5.0(
2
)
Major Home Repairs (General Contractor)

Serving Mccammon, ID and surrounding areas

In business since 2004

Free estimates

Emergency services offered

"Excellent service & response. Did not just install carpets; renovated entire home. Wall repair, painting, carpet installation, linoleum installation, caulking, powerwashing, co-ordinating countertop relacement, ceiling fan installation, deck reconstruction and more. An excellent company to work with. Actually, 6 star rating in my opinion. -Jack."
Recommended by100%of homeowners
Showing 1-10 of 24
Unfinished Carpentry questions, answered by experts

Yes, you will need a jack for a rim joist replacement. To prevent sagging and facilitate the removal of load-bearing wood, you’ll need to relieve the pressure from this joint before beginning work. 

Due to hydraulics and other specialized equipment, a sill plate and rim joist replacement are not typically a DIY project. Hiring a professional structural engineer and experienced contractors is the best approach to replacing rotted sill plates and rim joists.

You can enclose an open carport, however, there are several things to consider before opting to do so. You'll want to check local building codes and permit requirements before proceeding to make sure it’s legal. While you can sometimes stick-frame a carport enclosure, pre-fab kits are also available. Remember that you'll likely need to meet concrete slab regulations and provide lighting inside the structure. Both of which could substantially drive up costs.

To calculate the number of linear feet of baseboard you’ll need, measure the length of each wall of the room you’re installing them in as close to the floor as possible, rounding up to the next full linear foot. If it’s your first DIY molding job, having a few extra feet on hand for miscuts is a good idea.

Yes, most services include necessary frame modifications for proper door fitting. Confirm with your provider.

A cross brace for a fence gate should stretch from the top corner of the gate’s hinge side to the bottom corner of its latch side at a 45-degree angle to the bottom of the gate. This positioning distributes the bulk of the gate’s weight to the base of the post, taking pressure off the top hinge.

The Mccammon, ID homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.