Top-rated plumbers.

Get matched with top plumbers in Heidelberg, MS

Enter your zip and get matched with up to 5 pros

Need a pro for your plumbing project in Heidelberg, MS?

Select your specific project to find the pro for you.

TRUSTED BY HEIDELBERG, MS HOMEOWNERS

  • Average homeowner rating star icon4.3
    Average homeowner rating
  • Verified reviews icon38
    Verified plumbing services reviews

Find Plumbers in Heidelberg

Avatar for Neli Virtual Appliance Repair
Neli Virtual Appliance Repair
4.2(
679
)
Refrigeration System - Install or ReplaceRefrigeration System - Install or Replace - For BusinessRefrigeration System - Repair or Service+1 more

Serving Heidelberg, MS and surrounding areas

Approved

In business since 2016

Free estimates

Warranties offered

"I hired Neli over a week period for 3 different appliances, my dryer, washing machine, dishwasher, and even kitchen sink! I had a fantastic experience: 1. I fixed my dryer with Thomas' excellent remote guidance, changing the timer and the switch! Fabulous guidance Thomas, with lots of money saved! I learned a lot in the process. 2. I determined that there was no dishwasher leak and in the process learned how to check for leaks and trouble shoot for some common repair issues. It cost $40.00 but as I had some water on the floor, I was ready to get a new dishwasher. Now, I am confident that it wasn't a leak and caused by putting in the dishes in a funny manner and not a repair issue. I am using the dishwasher now again with no problem. 3. I determined with Thomas' help that the washing machine had a major problem and could have spun out of control into my wall....no question, it was time to get a new washing machine! This was a well spent $40.00--I even got Thomas advice on purchasing a new washing machine and what to look for. 4. I checked the drainage on my kitchen sink and learned how to empty out the "trap" and that most likely, I am okay, but what to swap out if I have continuing issues with slow drainage. In the end, I saved lots of money, gaining and learning valuable experience! Absolutely fabulous service!"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Response time1 day
Recommended by86%of homeowners
...
Showing 1-10 of 80
Plumbing questions, answered by experts

There are three main types of shower valves: pressure-balancing, thermostatic, and diverter. Pressure-balancing and thermostatic valves are both considered mixing valves because they regulate water flow and temperature, but they do so in different ways. A pressure-balancing valve senses changes in water pressure, such as from a flushing toilet, and adjusts the incoming hot and cold water to maintain a consistent temperature; these typically use a single knob. A thermostatic valve uses a thermostat to precisely control the water temperature and requires a separate control to adjust the water volume. A diverter valve directs the flow of water from one fixture to another, such as switching from a tub faucet to a showerhead in a tub-shower combination.

You can remove air from your shower pipes in a few simple steps. Turn off the water at the main water supply and open all the faucets in your home, starting with those closest to the water supply and working away from those. Let the faucets run dry, then flush all the toilets in your home until there is no more water in them. From there, turn the water supply back on and let it flow for 10 to 15 minutes until the sputtering stops. To finish, turn off your faucets and flush your toilets in the reverse order.

Yes. There are a variety of standard pipe sizes used in plumbing. The main supply line connecting your home to the street is either 3/4 or 1 inch in diameter. Supply lines are 3/4 inch in diameter. Individual components are 1/2 inch in diameter. Meanwhile, your main drainpipe is often 4 inches wide. Most shower and bathtub drains are 2 inches in diameter, most toilet drains are 3 inches in diameter, and most sink drainpipes are 1 1/4 or 1 ½ inches in diameter.

Pedestal sinks are bolted or screwed into the floor and the wall to prevent it from moving out of place. You may have to change or add to the bathroom flooring when installing a pedestal sink if the flooring was laid around the previous sink, not under it.

The average cost to replace a toilet fill valve is around $100, and prices range from $50 up to $150, depending on your location, the experience of the plumber, and how accessible your toilet is. In most cases, a professional plumber can replace your fill valve in under an hour, although it might take longer if they also need to fix or replace other components at the same time.

The Heidelberg, MS homeowners’ guide to plumbing services

From average costs to expert advice, get all the answers you need to get your job done.