Top-rated toilet pros.

Best toilet pros near Fillmore, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your toilet service project in Fillmore, UT?

Select your specific project to find the pro for you.

Top-Rated Toilet pros in Fillmore - Updated Nov 2026

Avatar for DML mechanical llc
DML mechanical llc
5.0(
15
)
Faucets, Fixtures and Pipes - Repair or ReplaceFaucets, Fixtures and Pipes - Repair or Replace - For Business

Serving Fillmore, UT and surrounding areas

Free estimates

Emergency services offered

Credit card accepted

"DML and his crew are amazing! I had a big project for them for my basement . They had to completely replace the subfloor of a large room and reinforce some of the crumbling infrastructure with a new retaining wall. They gutted, expanded, and remodeled the bathroom with new tile, sink, toilet, vent and fan, everything! I've already recommended them to two other people. Also, their prices are very reasonable."
Furnace
Commercial proyect
Home Duvan
Painting
Furnace

+75

Recommended by100%of homeowners
Replumb Specialties Inc.
3.9(
9
)
Faucets, Fixtures and Pipes - Repair or ReplaceFaucets, Fixtures and Pipes - Repair or Replace - For Business

Serving Fillmore, UT and surrounding areas

In business since 1992

Free estimates

Warranties offered

"RSI is a great replumb company. The actual replumbing was outstanding and we opted for the upgraded pro-plex fittings to increase our warranty from 10 to 25 years (not an up sell by Jamey - our choice). They also put in-place a dedicated recirculation line for our tankless water heater. The RSI team (Kenny and Milo) was expert at locating and replacing the old polybutylene piping with minimal impact to sheetrock, tiles, and fittings. They finished the work early but were delayed in finalizing the project due to a delay from the Regional Building Inspectors, not RSI's fault. Our only suggestions are 1) better daily clean-up, 2) better attention to detail repainting sheetrock (we had to repeatedly point out areas for a 'redo' and adjacent areas for touch-up) - this seemed harder to do that we expected (this is why we gave them a B rather than an A for quality). Jamey was very responsive to us and answered our questions/concerns thoroughly and promptly. We will recommend RSI our neighbors and friends.
"
Recommended by85%of homeowners
Avatar for Miller Plumbing
Miller Plumbing
0.5(
2
)
Drain Clog or Blockage - Clear

Serving Fillmore, UT and surrounding areas

In business since 2016

Free estimates

Offers commercial services

We're dedicated to providing our clients with the very best in service, installation, and repair to meet your plumbing needs. We have 15 years of industry experience. We specialize in mechanical piping and we offer a one year warranty on a variety of residential and commercial services. We take pride in the attention to detail put into each of the projects we're involved with. We're known for our quality work and the integrity of our business. We look forward to building long-term relationships with our clients, and guarantee your satisfaction.

Response time9 hrs
Toilets FAQs, answered by experts

In most cases, it’s better to repair a toilet than to replace it. Fixing issues like low water levels, running water, and flushing problems is less expensive than buying a new unit. Start thinking about replacement if the toilet is cracked, using excessive amounts of water, or is over 15 years old. Newer models are more water-efficient and clog less often than older models.

Yes, you should screw your flange to the subfloor, including cement. The best way to get this done is to predrill holes into the concrete using a hammer drill and a ¼-inch concrete bit. Be careful when you’re ready to bolt your flange down, as you can accidentally crack it. You can avoid this issue by not installing the screws too deep. Or, you can opt for a flange with a stainless steel ring so you don’t have to worry about cracking the plastic.

Replacing a standard toilet with an elongated one is straightforward. The two types can be installed using the same existing drainpipe and plumbing. If you have a small bathroom, make sure that an elongated toilet doesn’t violate local building codes for clearance, which is the space between fixtures and walls. 

Depending on the issue and materials, costs range from $150 to $500.

While you shouldn’t increase the flow of your low-flow toilet by adjusting the water level in the toilet bowl set by the manufacturer, you can make the flow as efficient as possible by ensuring the rim jets under the rim are unobstructed. To do this, use a mirror to look under the rim and scrub them with a toothbrush or a small wire to clear any debris stuck in the holes. You can also watch for leaks, make sure the internal components are in good shape, and replace them if necessary.

The Fillmore, UT homeowners’ guide to toilet services

From average costs to expert advice, get all the answers you need to get your job done.