Top-rated toilet pros.

Get matched with top toilet pros in Elsinore, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your toilet service project in Elsinore, UT?

Select your specific project to find the pro for you.

TRUSTED BY ELSINORE, UT HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon12
    Verified toilet services reviews

Find Toilet pros in Elsinore

Replumb Specialties Inc.
3.9(
9
)
Faucets, Fixtures and Pipes - Repair or ReplaceFaucets, Fixtures and Pipes - Repair or Replace - For Business

Serving Elsinore, UT and surrounding areas

In business since 1992

Free estimates

Warranties offered

"RSI is a great replumb company. The actual replumbing was outstanding and we opted for the upgraded pro-plex fittings to increase our warranty from 10 to 25 years (not an up sell by Jamey - our choice). They also put in-place a dedicated recirculation line for our tankless water heater. The RSI team (Kenny and Milo) was expert at locating and replacing the old polybutylene piping with minimal impact to sheetrock, tiles, and fittings. They finished the work early but were delayed in finalizing the project due to a delay from the Regional Building Inspectors, not RSI's fault. Our only suggestions are 1) better daily clean-up, 2) better attention to detail repainting sheetrock (we had to repeatedly point out areas for a 'redo' and adjacent areas for touch-up) - this seemed harder to do that we expected (this is why we gave them a B rather than an A for quality). Jamey was very responsive to us and answered our questions/concerns thoroughly and promptly. We will recommend RSI our neighbors and friends.
"
Recommended by85%of homeowners
Avatar for Miller Plumbing
Miller Plumbing
0.5(
2
)
Drain Clog or Blockage - Clear

Serving Elsinore, UT and surrounding areas

In business since 2016

Free estimates

Offers commercial services

We're dedicated to providing our clients with the very best in service, installation, and repair to meet your plumbing needs. We have 15 years of industry experience. We specialize in mechanical piping and we offer a one year warranty on a variety of residential and commercial services. We take pride in the attention to detail put into each of the projects we're involved with. We're known for our quality work and the integrity of our business. We look forward to building long-term relationships with our clients, and guarantee your satisfaction.

Response time9 hrs
Toilets questions, answered by experts

Yes, you should screw your flange to the subfloor, including cement. The best way to get this done is to predrill holes into the concrete using a hammer drill and a ¼-inch concrete bit. Be careful when you’re ready to bolt your flange down, as you can accidentally crack it. You can avoid this issue by not installing the screws too deep. Or, you can opt for a flange with a stainless steel ring so you don’t have to worry about cracking the plastic.

Your toilet handle might not come back up if the nut is loose or the bolt threads are stripped. Try to tighten the mounting nut and wrap plumber’s tape around the handle bolt to fix stripped threads. It’s possible the handle was improperly installed. If that’s the case, you can use the instructions above to correct the handle’s position. 

There are a few reasons why this could be the case. More than likely, your flapper is worn out and needs to be replaced. When it’s worn out, it lowers the water pressure during each flush leading to inefficient flushing. Luckily, replacing a toilet flapper is a simple repair that should only take about 30 minutes.

If you don’t replace a toilet flapper, your toilet tank will continue to empty and fill repeatedly, wasting water and running up your utility bills. Checking the flapper is a good first guess when dealing with a constantly running toilet. However, if these problems continue after replacing the flapper, you may need to hire a plumber to check and fix any bigger problems. 

The toilet should rest 10, 12, or 14 inches from the back wall. As for other clearances, 15 inches is the minimum distance from the flange to any side wall or nearby fixture, including the shower, tub, and sink. Modern codes also require at least 24 inches of clear space in front of the toilet.

The Elsinore, UT homeowners’ guide to toilet services

From average costs to expert advice, get all the answers you need to get your job done.