Top-rated electricians.

Get matched with top electricians in Silver Point, TN

Enter your zip and get matched with up to 5 pros

Need a pro for your electrical service project in Silver Point, TN?

Select your specific project to find the pro for you.

TRUSTED BY SILVER POINT, TN HOMEOWNERS

  • Average homeowner rating star icon4.7
    Average homeowner rating
  • Verified reviews icon111
    Verified electrical services reviews

Find Electricians in Silver Point

Avatar for Tri-State Water, Power & Air
Tri-State Water, Power & Air
5.0(
6
)
Fixed Generator - InstallGenerator - InstallGenerator - Install - For Business

Serving Silver Point, TN and surrounding areas

Approved (Corporate)

In business since 1992

Free estimates

Emergency services offered

We are the experts in the field of Whole Home Generator Sales and Installation, with over 20 years of experience in the game. We provide turn-key installation by licensed professionals - 24 hour emergency service - Remote Monitoring - Long term maintenance and service by factory trained technicians.

Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+3

87 neighbors recently requested a quote
Recommended by16%of homeowners
Avatar for W B Lightning Rods
W B Lightning Rods
4.6(
372
)
Lightning Protection - Install or Repair

Serving Silver Point, TN and surrounding areas

Approved

In business since 2001

Free estimates

Warranties offered

"Used this company previously and again it was a pleasure from beginning to end. I would give him 10 Stars if I could. Referred William to a close friend of mine and she was just as pleased. We both sleep better during our bad Florida thunderstorms. A friend of mine lost their home due to lightning. They got out just in time couldn’t save anything but their lives barely. I urge all to install lightning rods."
lightning protection
 Residential LPS
lightning protection
 Residential LPS
lightning protection

+79

Response time1 day
163 neighbors recently requested a quote
Recommended by96%of homeowners
Avatar for J&S Construction and Remodeling
J&S Construction and Remodeling
4.9(
33
)
Appliance (Major Electric Appliance) - Install or Replace

Serving Silver Point, TN and surrounding areas

Approved

In business since 2025

Free estimates

Emergency services offered

"I would highly recommend this company. Very honest and true to his word. Does very good work, i am very pleased and looking at a 2nd project with them once I save a bit more money! Money well spent to cover my patio and install 2 fans."
Bathroom floor
Ceiling fan install
Wheel chair ramp
Wheel chair ramp
Subfloor redoing

+161

3 neighbors recently requested a quote
...
Showing 1-10 of 105
Electrical questions, answered by experts

Yes, it’s possible to use a three-way switch as a two-way switch. You can use a three-way switch as a two-way switch by bypassing one of the traveler wires and using only one of the available traveler switch terminals.

To fix a tripped light switch, locate your home's electrical panel and identify the tripped circuit breaker. It will be in the "off" or neutral position. Flip the breaker entirely to the "off" position, then switch it back to the "on" position. If the breaker trips again immediately, there may be a short circuit or overload in the system, requiring further investigation. If the switch still doesn't work after resetting the breaker, check for loose wires or faulty components in the switch itself. It is always best to consult a licensed electrician for persistent issues and when in doubt.

Baking soda is an effective fire reduction method. However, flour and baking powder are very dangerous around flames. Flour is flammable and it can also conduct electricity. The combination can cause serious injury from electrical shock and worsen the situation by adding fuel to the fire. Baking powder is also not an option as it's also highly flammable. 

You can tell if a breaker is GFCI by looking for a red or yellow test and reset button that you can press in and out. You’ll know if an outlet is GFCI if the red reset button is located in between the two pronged sections.

Most LED bulbs have a plastic covering, while incandescent bulbs will be made from glass. This is because LED bulbs don’t produce as much heat as incandescent bulbs, so the covering doesn’t need to be as heat resistant. Also, an LED light bulb will usually have a marking on its base that identifies it as an LED.

The Silver Point, TN homeowners’ guide to electrical services

From average costs to expert advice, get all the answers you need to get your job done.