Top-rated carpenters.

Get matched with top carpenters in Madison Heights, MI

Enter your zip and get matched with up to 5 pros

Need a pro for your carpentry project in Madison Heights, MI?

Select your specific project to find the pro for you.

TRUSTED BY MADISON HEIGHTS, MI HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon237
    Verified carpentry services reviews

Find Carpenters in Madison Heights

Avatar for Christian Dangelo Finish Carpentry
Christian Dangelo Finish Carpentry
4.4(
7
)
Closet - BuildInterior Trim and Decorative Moldings - InstallWood Stairs and Railings - Install or Replace

Serving Madison Heights, MI and surrounding areas

Approved

In business since 2015

Free estimates

Credit card accepted

"Chris built a wardrobe closet, bedside bookcases, head board, bed frame with storage, dining nook bench, and a dining room table for me. Excellent work, prompt, cleaned up after every day. Super to work with and would highly recommend this professional!"
Response time3 days
1 neighbors recently requested a quote
Recommended by16%of homeowners
Avatar for Mr. Handyman of Bloomfield/Birmingham
Mr. Handyman of Bloomfield/Birmingham
3.8(
97
)
Window Frame - Repair - For Business

Serving Madison Heights, MI and surrounding areas

Approved

In business since 2002

Customers say: Quick response

"I called in a rush to have someone come and remove the door frame to get the old washer and dryer out and put the new one in. Brian was great! He was here within a couple of hours and knew just what I needed! All went well. I will use them again. Very happy with the service."
1 neighbors recently requested a quote
Recommended by70%of homeowners
Nothaft Carpentry
3.4(
5
)
Closet - BuildFurniture - Build CustomInterior Trim and Decorative Moldings - Install+3 more

Serving Madison Heights, MI and surrounding areas

Approved

In business since 1997

Free estimates

Emergency services offered

"Gary installed exterior steps leading from our kitchen to our backyard. We have a newly built home and he did an excellent job. When we are ready to do more wood work, we will hire him again. Dependable, affordable, and professional."
1 neighbors recently requested a quote
Recommended by100%of homeowners
McCords' Carpentry
New to Angi
Exterior Shutters - Repair or Restore

Serving Madison Heights, MI and surrounding areas

Approved

I've been honing my craft in the trades since I was old enough to swing a hammer... I always do my best to think outside of the box to problem solve issues and I like to think I'm pretty good at it too.\nI could do just about anything you would need a handyman to do... I've been framing houses and building stages for concerts since about 2015... For that reason my skills are a little too well rounded to specifically list off each and every one.

...
Showing 1-10 of 363
Carpentry questions, answered by experts

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

Baseboards don’t have to be nailed into studs. However, nailing them into studs adds to their stability. When studs aren’t available, you can secure them with drywall nails directly into the drywall and adhesive. Always aim to nail into studs, especially in high-traffic or impact-prone areas.

When building a house, it is customary to use 16d nails that measure 3 1/2 inches in length to construct the frame. These nails are crucial in providing the necessary support and stability for structural elements like joists and studs, which ensures a sturdy framework.

Yes, a 2x6 should hold a porch swing and safely support the load. A smaller joist runs the risk of it not offering enough support for the swing. If you have a joist smaller than 2x6, add additional bolstering support.

You should avoid drilling or cutting into load-bearing beams because removing material will weaken it and increase the risk of structural damage or even collapse. If you do need to drill into a load-bearing beam, speak with a structural engineer first to discuss where it’s safest to drill and the width and depth of the bit that’s safe to use.

The Madison Heights, MI homeowners’ guide to carpentry services

From average costs to expert advice, get all the answers you need to get your job done.