Top-rated welders.

Get matched with top welders in Unionville, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Unionville, VA?

Select your specific project to find the pro for you.

Find Welders in Unionville

Grady's Painting Plastering/Construction
2.0(
174
)

Serving Unionville, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Recommended by57%of homeowners
Avatar for Rivera Welding
Rivera Welding
5.0(
6
)

Serving Unionville, VA and surrounding areas

In business since 2022

Free estimates

"Fast response on initial request, early for estimate and installation. Very friendly and professional. Great Iron work and installation. Better than we expected, very creative."
Response time11 hrs
Recommended by100%of homeowners
Avatar for High and Low Welding
High and Low Welding
5.0(
2
)

Serving Unionville, VA and surrounding areas

In business since 2023

Free estimates

Emergency services offered

"High & Low Welding fabricated & installed wrought iron railings for my home. The work was done professionally. I'm very happy with the work done. I recommend High & low Welding to anyone."
Welding
Welding Project
Install handrails
Welding
Welding Project

+12

Recommended by100%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)

Serving Unionville, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"At some point, we had a snake get into the air warming portion of our woodstove. When we went to start the stove up in the fall, the warmed air smelled terrible and made the whole house smell awful! The job was a pretty big challenge because the whole top of the stove had to be cut off then welded back on after the remains of the snake had been removed. Since the stove weighs quite a bit (a couple of hundred pounds at least) and is difficult to move, the work needed to be done in our basement...someone had to be able to do the welding in my house. It was a major job cutting the top of the cast iron stove off, but Mr. Perez was very patient and spent the time necessary to do the job correctly. Mr. Perez is very well mannered and is someone you can trust having in your house."
Response time2 days
Recommended by100%of homeowners
Avatar for NV Pro Services
NV Pro Services
4.5(
8
)

Serving Unionville, VA and surrounding areas

Free estimates

Emergency services offered

Credit card accepted

"We needed some emergency tree work done after one of our recent storms. Nick was there early the next day and was able to take care of the problem quickly and safely. Would definitely hire him again."
Power was dumptruck
Back yard lights on
Power was commercial building
Side, red mulch lights
Power wash heavy equipment

+36

Recommended by100%of homeowners
Showing 1-10 of 43
Welding questions, answered by experts

Some welding projects, such as repairing pipes or fences, require travel, whereas others, like furniture repair, do not necessarily require the welder to come to you. Travel and overhead factor into the overall cost of your welding project. Some of the most common welding projects include:

  • Metal furniture repair: $35–$100

  • Pipe repair: $200–$1,000

  • Small gates: $550–$750

  • Fencing: $1,200–$1,800

  • Fabricated sheet metal welding: $750–$2,500

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Yes, but you’ll need reliable steel-cutting tools and safety gear to get started. Shipping containers are typically around ¾ inch thick, so it’s entirely possible to cut through them, but experience and the right equipment are very important. When possible, try to get a container as close to the size you want it as possible.

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

The Unionville, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.