Top-rated welders.

Best welders near Rixeyville, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Rixeyville, VA?

Select your specific project to find the pro for you.

Top-Rated Welders in Rixeyville - Updated Nov 2026

Grady's Painting Plastering/Construction
2.0(
174
)
Wrought Iron Fence - Repair or Weld

Serving Rixeyville, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Rixeyville, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"I had an unusual request when I called Mr. Perez, the owner of Eastcoast Welding and Fabricating. It was to weld or solder a very old halloween decoration that our family just couldn't say good-bye to. I met Mr. Perez in Ruckersville, where Eastcoast is located. He took our broken pumpkin and performed a miracle. One hour later he was back with our pumpkin looking better then ever. We are thrilled! Thank you Marcos Perez for accepting my challenge and for delivering such an unexpected "Bang for my Buck!" T.B. Spotssylvania, Va."
Response time2 days
Recommended by100%of homeowners
Avatar for Energy Wise Heating & A/c inc.
Energy Wise Heating & A/c inc.
4.9(
15
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Rixeyville, VA and surrounding areas

In business since 1998

Free estimates

Emergency services offered

"Matt and his crew were on time, professional and on time. We first called a big name company that you may see on the back of a truck. Well that company quoted us $10,000-$15,000 for less work; at that point it was ONLY the furnace. I called Matt for a second opinion. Obviously, he quoted me for half the price of the back of the truck company WITH the water heater added in. Total work done: replaced furnace and outside unit, replaced water heater, installed water pump, installed 2 EcoBee thermostats. The big name company was ONLY doing the furnace and outside unit. We will call Matt for our future needs."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by100%of homeowners
Showing 1-10 of 40
Welding FAQs, answered by experts

Welding is the process of using extreme heat—and, sometimes, pressure—to attach two pieces of metal. In contrast, metal fabrication is a more involved process that can include welding, sheet metal work, bending, and other forms of metal manipulation. Metal fabrication is a large-scale project that may or may not involve welding, while welding is more often a step in larger fabrication projects.

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

The Rixeyville, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.