Top-rated welders.

Get matched with top welders in Falmouth, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Falmouth, VA?

Select your specific project to find the pro for you.

Find Welders in Falmouth

Avatar for Sunlight Welding LLC
Sunlight Welding LLC
5.0(
6
)

Serving Falmouth, VA and surrounding areas

Approved

In business since 2024

Free estimates

Credit card accepted

"There was a mistake in building the rail, but sunlight welding did a fantastic job of fixing the issue and doing right by the customer. Great customer service and a guiding light of how to turn around a situation."
Railing Springfield
Railing Springfield
Railing Springfield
Iron Gate
Response time9 hrs
11 neighbors recently requested a quote
Recommended by80%of homeowners
Grady's Painting Plastering/Construction
2.0(
174
)

Serving Falmouth, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
General Steel
New to Angi

Serving Falmouth, VA and surrounding areas

Approved

In business since 2000

Free estimates

Credit card accepted

General Steel is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Response time8 hrs
33 neighbors recently requested a quote
Avatar for Rivera Welding
Rivera Welding
5.0(
6
)

Serving Falmouth, VA and surrounding areas

In business since 2022

Free estimates

"Fast response on initial request, early for estimate and installation. Very friendly and professional. Great Iron work and installation. Better than we expected, very creative."
Response time11 hrs
Recommended by100%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)

Serving Falmouth, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"At some point, we had a snake get into the air warming portion of our woodstove. When we went to start the stove up in the fall, the warmed air smelled terrible and made the whole house smell awful! The job was a pretty big challenge because the whole top of the stove had to be cut off then welded back on after the remains of the snake had been removed. Since the stove weighs quite a bit (a couple of hundred pounds at least) and is difficult to move, the work needed to be done in our basement...someone had to be able to do the welding in my house. It was a major job cutting the top of the cast iron stove off, but Mr. Perez was very patient and spent the time necessary to do the job correctly. Mr. Perez is very well mannered and is someone you can trust having in your house."
Response time2 days
Recommended by100%of homeowners
...
Showing 1-10 of 56
Welding questions, answered by experts

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

Some welding projects, such as repairing pipes or fences, require travel, whereas others, like furniture repair, do not necessarily require the welder to come to you. Travel and overhead factor into the overall cost of your welding project. Some of the most common welding projects include:

  • Metal furniture repair: $35–$100

  • Pipe repair: $200–$1,000

  • Small gates: $550–$750

  • Fencing: $1,200–$1,800

  • Fabricated sheet metal welding: $750–$2,500

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

The best thing to cut metal pipe is a durable pipe cutter that is made for metal. You may want to measure the diameter of the pipes before purchasing a pipe cutter to ensure it will be able to cut your metal pipes. Opt for a heavy-duty option to cut through metal like steel or cast iron.

The Falmouth, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.