Top-rated welders.

Get matched with top welders in Locust Grove, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Locust Grove, VA?

Select your specific project to find the pro for you.

Find Welders in Locust Grove

Grady's Painting Plastering/Construction
2.0(
174
)

Serving Locust Grove, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
Avatar for Rivera Welding
Rivera Welding
5.0(
6
)

Serving Locust Grove, VA and surrounding areas

In business since 2022

Free estimates

"Fast response on initial request, early for estimate and installation. Very friendly and professional. Great Iron work and installation. Better than we expected, very creative."
Response time11 hrs
Recommended by100%of homeowners
Avatar for High and Low Welding
High and Low Welding
5.0(
2
)

Serving Locust Grove, VA and surrounding areas

In business since 2023

Free estimates

Emergency services offered

"High & Low Welding fabricated & installed wrought iron railings for my home. The work was done professionally. I'm very happy with the work done. I recommend High & low Welding to anyone."
Welding
Welding Project
Install handrails
Welding
Welding Project

+12

Recommended by100%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)

Serving Locust Grove, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"At some point, we had a snake get into the air warming portion of our woodstove. When we went to start the stove up in the fall, the warmed air smelled terrible and made the whole house smell awful! The job was a pretty big challenge because the whole top of the stove had to be cut off then welded back on after the remains of the snake had been removed. Since the stove weighs quite a bit (a couple of hundred pounds at least) and is difficult to move, the work needed to be done in our basement...someone had to be able to do the welding in my house. It was a major job cutting the top of the cast iron stove off, but Mr. Perez was very patient and spent the time necessary to do the job correctly. Mr. Perez is very well mannered and is someone you can trust having in your house."
Response time2 days
Recommended by100%of homeowners
Avatar for EXCEL HEATING & COOLING
EXCEL HEATING & COOLING
4.5(
28
)

Serving Locust Grove, VA and surrounding areas

In business since 1953

Free estimates

Emergency services offered

"Wonderful! They were so knowledgeable and friendly! We have an old house so they helped us figure out the best heating and cooling system for us. It couldn’t have been a better process AND now we are beyond comfortable in our 1920 craftsman house!"
Recommended by91%of homeowners
Showing 1-10 of 42
Welding questions, answered by experts

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

Costs depend on unit complexity, labor, wall mounting needs, and additional accessories like floating shelves.

The Locust Grove, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.