Top-rated welders.

Get matched with top welders in Castleton, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Castleton, VA?

Select your specific project to find the pro for you.

Find Welders in Castleton

Grady's Painting Plastering/Construction
2.0(
174
)
Wrought Iron Fence - Repair or Weld

Serving Castleton, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Castleton, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"At some point, we had a snake get into the air warming portion of our woodstove. When we went to start the stove up in the fall, the warmed air smelled terrible and made the whole house smell awful! The job was a pretty big challenge because the whole top of the stove had to be cut off then welded back on after the remains of the snake had been removed. Since the stove weighs quite a bit (a couple of hundred pounds at least) and is difficult to move, the work needed to be done in our basement...someone had to be able to do the welding in my house. It was a major job cutting the top of the cast iron stove off, but Mr. Perez was very patient and spent the time necessary to do the job correctly. Mr. Perez is very well mannered and is someone you can trust having in your house."
Response time2 days
Recommended by100%of homeowners
Avatar for Energy Wise Heating & A/c inc.
Energy Wise Heating & A/c inc.
4.9(
15
)
Metal Stairs and Railings - RepairMetal Structure or Object - Weld or Cut

Serving Castleton, VA and surrounding areas

In business since 1998

Free estimates

Emergency services offered

"Matt and his crew were on time, professional and on time. We first called a big name company that you may see on the back of a truck. Well that company quoted us $10,000-$15,000 for less work; at that point it was ONLY the furnace. I called Matt for a second opinion. Obviously, he quoted me for half the price of the back of the truck company WITH the water heater added in. Total work done: replaced furnace and outside unit, replaced water heater, installed water pump, installed 2 EcoBee thermostats. The big name company was ONLY doing the furnace and outside unit. We will call Matt for our future needs."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by100%of homeowners
Showing 1-10 of 34
Welding questions, answered by experts

The average cost for a welding project is about $300, with typical costs ranging from $125 to $490. However, prices can be as low as $125 for very small jobs or exceed $1,200 for large or complex projects. Welders typically charge an hourly rate between $65 and $150, depending on their experience, and many charge a minimum fee to cover overhead and travel expenses. The total cost is influenced by several factors, including labor, the cost of materials like metal rods and shielding gas, the type of metal being welded, the project's size and complexity, and your geographic location. For a precise quote, it's best to ask a local welder for an estimate based on your specific project.

Cutting round ductwork requires precision and the right tools. A duct cutter, specifically designed for circular ducts, is ideal. First, mark the cutting line on the duct using a measuring tape and pencil. Then, position the duct cutter's blade on the marked line. Apply steady pressure, rotating the cutter around the duct. The sharp blade creates a clean, precise cut. Alternatively, a reciprocating saw with a metal-cutting blade can be used for larger round ducts. Ensure the duct is securely held in place while making the cut to prevent slips and maintain accuracy.

Costs depend on unit complexity, labor, wall mounting needs, and additional accessories like floating shelves.

Yes, but you’ll need reliable steel-cutting tools and safety gear to get started. Shipping containers are typically around ¾ inch thick, so it’s entirely possible to cut through them, but experience and the right equipment are very important. When possible, try to get a container as close to the size you want it as possible.

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

The Castleton, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.