Top-rated welders.

Get matched with top welders in Sperryville, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Sperryville, VA?

Select your specific project to find the pro for you.

Find Welders in Sperryville

Grady's Painting Plastering/Construction
2.0(
174
)

Serving Sperryville, VA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
General Steel
New to Angi

Serving Sperryville, VA and surrounding areas

Approved

In business since 2000

Free estimates

Credit card accepted

General Steel is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests, and make their concerns the basis of our business.

Response time8 hrs
42 neighbors recently requested a quote
Avatar for Rivera Welding
Rivera Welding
5.0(
6
)

Serving Sperryville, VA and surrounding areas

In business since 2022

Free estimates

"Fast response on initial request, early for estimate and installation. Very friendly and professional. Great Iron work and installation. Better than we expected, very creative."
Response time11 hrs
Recommended by100%of homeowners
Avatar for East Coast Welding and Fabricators
East Coast Welding and Fabricators
5.0(
2
)

Serving Sperryville, VA and surrounding areas

In business since 2018

Free estimates

Credit card accepted

"At some point, we had a snake get into the air warming portion of our woodstove. When we went to start the stove up in the fall, the warmed air smelled terrible and made the whole house smell awful! The job was a pretty big challenge because the whole top of the stove had to be cut off then welded back on after the remains of the snake had been removed. Since the stove weighs quite a bit (a couple of hundred pounds at least) and is difficult to move, the work needed to be done in our basement...someone had to be able to do the welding in my house. It was a major job cutting the top of the cast iron stove off, but Mr. Perez was very patient and spent the time necessary to do the job correctly. Mr. Perez is very well mannered and is someone you can trust having in your house."
Response time2 days
Recommended by100%of homeowners
Avatar for Energy Wise Heating & A/c inc.
Energy Wise Heating & A/c inc.
4.9(
15
)

Serving Sperryville, VA and surrounding areas

In business since 1998

Free estimates

Emergency services offered

"The Energy Wise team was great. The technicians arrived on time and explained everything very well. They were very respectful of our house and completely the work quickly. The owner Matt came out as well to make sure everything was in working order and even gave some advice that went above and beyond. Very positive experience."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by100%of homeowners
Showing 1-10 of 30
Welding questions, answered by experts

While a high-speed circular saw will cut through metal, and even cut through multiple sheets at once, the fast-spinning saw blades create a lot of heat. This heat can damage paint and other protective coatings, leading to serious problems like rust over time. The cost to paint a metal roof again to avoid this damage is typically an additional $0.50 to $1 per square foot.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Choosing the right metal fabricator for your project begins with research. Find a reputable fabrication company by searching for reputable contractors in your area, and then reviewing photos of their previous work, customer reviews, and photos of the company’s workshop.

Once you’ve narrowed down the list, contact the companies to ask about the types of metal fabrication projects they specialize and inquire about guarantees and warranties on workmanship. You should also ensure the company uses high-quality material, and ask about the schedule and turnaround time for your proposed project.

The cost to weld aluminum averages about $14 to $22 per pound. The type of metal factors into the overall cost of any welding project due to the cost of the materials and the expertise required to work with it. Some of the most common metals used by welders include:

  • Magnesium alloy: $7–$16 per pound

  • Low-carbon steel: $11–$12 per pound

  • Stainless steel: $13–$15 per pound

  • Copper/brass: $24–$29 per pound

  • Cast iron: $38–$79 per pound

  • Titanium: $60–$85 per pound

There are a few things you can ask welders before you hire them to get an idea of their experience and ability levels:

  • Are you licensed and certified?

  • How long have you been in the welding business?

  • Do you commonly do the type of welding I need?

  • Do you offer any kind of warranty for your work?

  • Do you charge by the hour or by the project?

  • How long do you expect my welding project to take?

  • What steps do you take to minimize errors in your work?

The Sperryville, VA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.