Top-rated well and pump technicians.

Best well and pump technicians near Accomac, VA

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Accomac, VA?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Accomac - Updated Nov 2026

Avatar for Bud Hypes Plumbing & Sewer Service
Bud Hypes Plumbing & Sewer Service
3.9(
28
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Accomac, VA and surrounding areas

In business since 1981

Emergency services offered

Credit card accepted

"I was very pleased with the service. Evidently the guts who did the estimate were not the same ones who came to do the work. they got the work done and cleaned up well but were aggravated that they were not adequately prepared for the job."
Recommended by75%of homeowners
Avatar for A-1 Eastern Shore Waterproofing
A-1 Eastern Shore Waterproofing
4.8(
6
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Accomac, VA and surrounding areas

In business since 1996

Free estimates

Emergency services offered

"The work done is wonderful, we had this put in last year and we've had no problems at all. We had a big storm here last week and everything was fine. It took us a while to find someone we trust, but we trusted Richard Legnaioli. Richard is just a wonderful person and is very pleasant to talk to. I personally would give him an A rating."
Recommended by100%of homeowners
Avatar for Christopher Plumbing
Christopher Plumbing
3.7(
3
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Accomac, VA and surrounding areas

In business since 2000

Emergency services offered

At Christopher plumbing, we are focused on providing exceptional 24 hour services with the highest levels of customer satisfaction & we will do everything we can to meet your expectations. With a variety of offerings to choose from, we're sure you'll be happy working with us. Because we're a small business we don't have the huge overhead expenses that you pay for so we are able to save you money with top of the line technicians. Our excellent reputation and long list of satisfied clients attest to our superior craftsmanship, attention to detail, clear communication, honesty and integrity. We offer discounts for seinors and military.

Recommended by66%of homeowners
Wells and Pumps FAQs, answered by experts

Although air in your water lines won’t affect the overall quality of your water, it will lead to problems with your well water system if not addressed. Over time, too much air in your water lines can create blockages in your pipes, cause insufficient water flow to your taps and appliances, loosen pipes, and potentially damage important components of your well including your well pump and pressure tank. 

Schedule annual inspections, monitor water pressure, and address minor issues promptly to avoid major repairs.

If your well pump gets stuck in its casing, you may be able to free it loose by gently wiggling the line or by vibrations from tapping the line with a hammer. However, if your pump is stuck in a buildup of minerals around the casing, you’ll probably have to call in a well pump contractor to get it out. They’ll likely use a muriatic acid solution—a strong, corrosive acid—to break down the minerals and free the pump loose. 

To avoid a stuck pump in the future, experts recommend a professional well cleaning once every 10 years. 

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Repairs typically take 2-4 hours. Complex issues may require additional time.

The Accomac, VA homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.