Vortex Filtration is a well water storage tank filtration system. "WE DONOT SERVICE WELLS & PUMPS, WE ADD FILTERATION TO WELLS & PUMPS, TO CLEAN WATER AND STORAGE TANKS, ALLOWING YOUR WATER TO BE CLEANER THAN A SWIMMING POOL!". Our systems go into storage tanks with a minimum of 2,000 gallons and up. \n\nIf you are having trouble with clogged filters, dirty water, water heater problems, iron and mineral stains in your toilets and other well water storage tank issues, call us to see what we can do for you. \n\nWe keep well water storage tanks crystal clear and your water system trouble free.
"Fixed shower but stated Toilet not on work order but suggested remedy. To keep in mind: If you need more than one thing done, Be sure to specify on initial work order as they will only do what is on work order from AHS"
We're dedicated to providing our clients with the very best in service, installation, and repair to meet your plumbing needs. We have 15 years of industry experience. We specialize in mechanical piping and we offer a one year warranty on a variety of residential and commercial services. We take pride in the attention to detail put into each of the projects we're involved with. We're known for our quality work and the integrity of our business. We look forward to building long-term relationships with our clients, and guarantee your satisfaction.
After flushing the toilet, you should have about half a tank full of water. While the exact amount of water you’ll have will vary, you want to make sure you have enough to cover the bottom of the bowl and enough to sit above the P-trap drain. While low water in your toilet bowl can indicate a problem, too much water can also be cause for concern.
The average cost to hire a plumber is typically between $45 and $200 per hour, with a common average rate around $125 per hour. This cost can vary based on your location, the plumber's experience, and the complexity of the job. Rates are often broken down by experience level: an apprentice may charge $45 to $90 an hour, a journeyman $60 to $110 an hour, and a master plumber $80 to $200 an hour. While hourly rates are standard, some plumbers may charge a flat fee for routine projects or offer project-based pricing. It's also common for plumbers to charge a minimum service or trip fee. For reference, some typical flat-rate costs for common jobs include: drain unclogging ($220), leaky faucet repair ($270), burst pipe repair ($400), toilet repair ($300), and water heater repair ($600). Note that these rates are for standard service hours; emergency, holiday, and after-hours calls will cost significantly more.
According to the Uniform Plumbing Code (UPC), the distance between your trap and the vent should be no more than 6 feet. For your vent to work properly, it needs to feed into the drain line within 6 feet of trapways that connect to it. Using this formula, you should be able to determine whether you will need multiple vent lines.
You generally cannot replace a 10-inch rough-in toilet with a 12-inch model without making significant plumbing updates. A 12-inch rough-in toilet will not fit a 10-inch rough-in space because the floor drain is in the wrong position. To accommodate the larger toilet, you would need to move the drainpipe, which could cost between $0.75 and $30 per linear foot, plus labor. In most cases, it is more cost-effective and simpler to purchase a new 10-inch rough-in toilet. However, it is possible to install a 10-inch rough-in toilet in a 12-inch space by using a longer connector.
The order of your bathroom renovation should prevent damage to the completed work. Start with demolition and removing the old fixtures. Then, address structural repairs or water damage, if needed. Next, tackle the rough-in phase for plumbing and electrical work, install waterproofing, and work on wall treatments like tile or paint. Install your shower or bathtub, toilet, vanity, and sink. Flooring goes in after major fixtures but before the toilet. Lastly, install new lighting fixtures, mirrors, and other finishing touches as desired.
The Annabella, UT homeowners’ guide to toilet services
From average costs to expert advice, get all the answers you need to get your job done.
Everyone can relate to having toilet issues—we’ve all been there. There are several reasons why your toilet might need repairs, and the cost varies based on the damage.
Worried about water leaking around your toilet? You may have a faulty toilet flange. Learn more about the cost to replace a toilet flange in our guide.
Before purchasing and installing a new toilet, you need to know the toilet rough-in measurement to ensure proper integration. Here’s how to get it done.
Leaky toilet tank sounds driving you crazy? It might be your toilet flapper. Here’s how to choose the right size toilet flapper to save water and money.
Toilets are a mainstay of American bathrooms, but is it time for a bidet? Before you decide, here’s everything you need to know about bidets versus toilets.
