Top-rated contractors.

Get matched with top contractors in Jefferson, PA

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Jefferson, PA?

Select your specific project to find the pro for you.

Find Contractors in Jefferson

Avatar for Muirs General Contracting llc
Muirs General Contracting llc
5.0(
4
)
Major Home Repairs (General Contractor)

Serving Jefferson, PA and surrounding areas

In business since 2018

Free estimates

Emergency services offered

"Things went smoothly from beginning to end. Very courteous, job done in a timely manner. Employees were very kind and skilled. Mr Muir was very helpful in getting all my projects completed. Would highly recommend him to anyone."
Prep
Deck extension, smoke shack roof build, house rot replaced
Basement remodel
Drop ceiling
Roof replaced + new A frame roof install

+376

Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Jefferson, PA and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Jefferson, PA and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for CCK Painting LLC
CCK Painting LLC
5.0(
5
)
Major Home Repairs (General Contractor)

Serving Jefferson, PA and surrounding areas

In business since 2022

Free estimates

"Easy to work with and was very helpful to help us achieve the final look we were looking for in our renovation. The crew was there when they were supposed to be and finished the job before expected which was a huge relief. The crew kept the work area clean and clutter free. I would highly recommend."
Painting - Interior Project
Finished door
Painting - Interior Project
Door needed some prep work done but turned good!
Painting - Interior Project

+38

Recommended by100%of homeowners
Showing 1-10 of 38
Unfinished Carpentry questions, answered by experts

It’s best to use two screws to secure deck boards into every joist. Securing the boards to every joist makes the deck more structurally sound, while using two screws on the outer sides of the boards can help prevent warping and cupping.

You can enclose an open carport, however, there are several things to consider before opting to do so. You'll want to check local building codes and permit requirements before proceeding to make sure it’s legal. While you can sometimes stick-frame a carport enclosure, pre-fab kits are also available. Remember that you'll likely need to meet concrete slab regulations and provide lighting inside the structure. Both of which could substantially drive up costs.

Installing a tongue-and-groove wall requires similar techniques to those associated with installing shiplap. However, because of the precision necessary to make each board fit perfectly and the increased material prices, the cost is higher than that of shiplap installations. Expect to spend between $2 and $6 more per square foot for tongue-and-groove walls versus shiplap ones.

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

Metal stud framing parts include the studs themselves, upper and lower tracks that act as top and bottom wall plates, various angle fasteners and clips, screws for fastening pieces togeher, metal straps, c-channel supports, and thicker steel supporting structures. Roof framing metal components include pre-fabricated trusses, heavy-gauge stud pieces, and various plates and fasteners.

The Jefferson, PA homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.