EVERYTHING IS LESS PRECISE It seems that the contractor?s underlying attitude was that ?this is just a garage,? but the resulting construction was more in line with building a shed. Window headers were left not completed. Cement-coated, scrap wood was used in visible portions of the exterior. Expensive siding (owner provided) was installed poorly, with trim regularly popping off and becoming detached. Loft stairs, although specified to be construction grade, appear to be styled to meld with ?The Little Rascal?s? club house; with varying sized treads and an OSB floored landing?the contractor tried to charge extra for this because they were ?winders!? Not enough anchor bolts were ordered to secure the floor plates; at the contractee?s insistence, Tapcons were used to make up for this error. Most of these were not driven in sufficiently?likely because the pilot holes weren?t drilled deep enough. A haphazard latticework of blocking and support for the loft trusses made this area impossible to insulate to code. Much of this had to be removed and properly reinstalled to obtain the required insulation thickness without excessive compression. To make up for a shortfall of approximately 18? of drip edge, a scrap piece was installed over the top of the existing edge. This makeshift installation would have directed rain into the roof, if the contractee had not corrected this error. The contractor?s trademark ?electrical entrance thru the foundation? was executed poorly with the electrical entrance conduit neither within the stud wall, nor outside of it. This construction trademark was supposed to make the electrical entrance disappear. However, the result is that the 2? conduit protrudes from an interior wall; making it impossible to conceal and difficult to sheathe. It would have been more aesthetic to do a conventional outside entrance.
COULD NOT MEET CODE REQUIREMENTS When the Building Permit was issued, the Code Enforcement Officer sent along requirements for Bracing for Overhead Doors in Seismic Areas. This document was promptly relayed to the contractor?who ignored it during construction. The contractee had to facilitate a meeting between the CEO and the contractor, and still, the issue was not resolved until (at the urging of the contractee) the eleventh hour. Throughout the project, the contractor appeared either not to understand the requirements, or was culturally unwilling to comply with them. This project also included a change order in the form of an extended roof eve and a cantilevered balcony. To the contractor?s credit, he was willing to accommodate the change and conferred with the building materials supplier for the engineering requirements. However, when the CEO requested the engineering report after the additions were completed, the contractee discovered that there was no written or formal report. To receive a Temporary Certificate of Occupancy, the contractee had to work with the building materials supplier (who graciously worked with their materials supplier) to generate a Structural Engineering Report. Although his assistance was requested, the contractor abstained from any involvement during this process.
DISREGARDED SPECIFICATIONS A few of these omissions were minor, like cutting off the ends of the gamble braces instead of beveling them, or using OSB for the loft flooring instead of the specified plywood. But for the slab concrete, the contractor ordered a #3000lb mix, instead of the specified #4000lb mix. The contractor?s Mason did a fine job of finishing the floor, but it cracked diagonally in several quadrants. I can?t help thinking that if the specified mix were used, the foundation wouldn?t have cracked as severely.
POOR COMMUNICATIONS WITH EMPLOYEES AND COORDINATION OF MATERIALS Basically, the contractee needed to supervise this project, because the contractor did not, and was rarely onsite. Unfortunately, the contractee realized this necessity late in the project. Several days after the slab was finished, the lone Mason hastily arrived, followed shortly by the cement truck. Soon, the Mason was rapidly filling buckets of concrete from the truck and pouring them throughout the curb, without any assistance. Realizing that no help was forthcoming and that the resulting job would be poor, the contractee assisted the Mason by distributing buckets of concrete, so that he could perform his expertise of vibrating (with his reciprocating saw) and finishing the concrete. Despite this effort, the resulting curb is poorly finished and leaks whenever it rains. The change order of the extended roof and balcony were charged separately and performed on a Labor and Materials basis. A significate amount labor was unnecessarily used because the contractor failed to inform the workers that a change order was in effect, requiring them to dismantle a considerable amount of the previous day?s construction. This waste of paid labor reinforced the notion that a ?change order? is a contractor?s ?license to steal.? A half-round window was specified to be installed over the balcony door. After the window had been received, the contractor informed the contractee that the window could not be installed because of the truss construction. In the contractor?s defense, I will state again, that the project did not have architectural plans; however, a knowledgeable contractor should know from experience what accoutrements will work with various types of construction. Of course, the contractor would not refund the cost of the window. Accordingly, just as with the code compliance issue; the contractee had to solve the problem by designing an installation for the window within the truss structure.
THE PROS: The contractor, Charles Duffy is a most congenial, warm and friendly person. His passion for deer hunting is unpatrolled and is always willing to share his vast knowledge of the sport with his clients. As such, it is wise for prospective clients not to schedule projects during, or allow them to overlap into the deer season, such as this one did. The contractor did an excellent job of removing all construction and demolition debris from the site. However, a better job of retrieving lost fasteners is necessary, as I am still picking nails from my driveway?one year later. "},"url":"https://www.angi.com/companylist/us/ny/bloomingdale/duffy%27s-builders-and-general-contracting-reviews-9339106.htm"},"position":9},{"@type":"ListItem","item":{"@type":"LocalBusiness","name":"Custom Overhead Door Inc","address":{"@type":"PostalAddress","addressRegion":"NY","addressCountry":"US"},"review":{"@type":"Review","author":{"@type":"Person","name":"Mark D."},"reviewBody":"Owner William \"Tim\" Miner informed me doors were of poor quality. Tried to sell me new doors instead and refused installation job because of the attempt at an upsale. I do not recommend."},"url":"https://www.angi.com/companylist/us/ny/chatham/custom-overhead-door-inc-reviews-308973.htm"},"position":10}]}
TV Antenna Installation reviews from real Angi homeowners in Bloomingdale, NY
The best possible service! There was practically no waiting time to start the project and the work was completed very fast. Anthony was very honest and straightforward about the prices, didn't have any objections to my own choice of fireplace insert (although he did offer his help in...
Owner William "Tim" Miner informed me doors were of poor quality. Tried to sell me new doors instead and refused installation job because of the attempt at an upsale. I do not recommend.
US Repairs LLC is a locally owned and operated company that values honesty and integrity in all aspects of our business. Our dedicated team of professionals have years of hands on experience, to provide innovative ideas and suggestions tailored to your projects. Our services are customized to your individual needs, paying close attention to the details of each project that we are involved with. Please feel free to contact us today!
US Repairs LLC is a locally owned and operated company that values honesty and integrity in all aspects of our business. Our dedicated team of professionals have years of hands on experience, to provide innovative ideas and suggestions tailored to your projects. Our services are customized to your individual needs, paying close attention to the details of each project that we are involved with. Please feel free to contact us today!
Hurricane Generators is dedicated to delivering a superior experience from start to finish—backed by prompt service, attention to detail, and a commitment to your complete satisfaction. When the power goes out, we’re here for you with 24/7 emergency service and reliable solutions you can count on. We proudly work with top brands like Generac, Cummins, and Champion to match every homeowner with the ideal generator for their needs. From expert installation to ongoing maintenance, our team ensures your system is ready whenever you need it most. With Hurricane Generators, you get more than just a product—you get a partner you can trust. We return calls promptly, show up on time, and deliver on every promise. And with our guaranteed competitive pricing, you can have peace of mind knowing you’re getting exceptional value along with exceptional service.
"project has not yet been completed"
Gina P on May 2025
Hurricane Generators is dedicated to delivering a superior experience from start to finish—backed by prompt service, attention to detail, and a commitment to your complete satisfaction. When the power goes out, we’re here for you with 24/7 emergency service and reliable solutions you can count on. We proudly work with top brands like Generac, Cummins, and Champion to match every homeowner with the ideal generator for their needs. From expert installation to ongoing maintenance, our team ensures your system is ready whenever you need it most. With Hurricane Generators, you get more than just a product—you get a partner you can trust. We return calls promptly, show up on time, and deliver on every promise. And with our guaranteed competitive pricing, you can have peace of mind knowing you’re getting exceptional value along with exceptional service.
WB Lightning Rods is a third-generation lightning protection contractor. Family Owned and operated for over 60 years. installing U.L. Listed Lightning protection systems, All Over the East coast, Midwest south east and south west regions of the U.S. Installations on Residential Homes, Estate Properties, Agricultural and Equestrian Properties. Lightning Protection for trees is also available. No job to big or small References upon Request. Contact us today for a no cost or obligation estimate. We look forward to working with you on your Lightning Protection Project. Thank you. **WE ARE NOT ELECTRICIANS** **WE ONLY INSTALL LIGHTNING PROTECTION SYSTEMS **
"Great company, they were fast, friendly, & accommodating. I would definitely use them again."
Jennifer B on October 2024
WB Lightning Rods is a third-generation lightning protection contractor. Family Owned and operated for over 60 years. installing U.L. Listed Lightning protection systems, All Over the East coast, Midwest south east and south west regions of the U.S. Installations on Residential Homes, Estate Properties, Agricultural and Equestrian Properties. Lightning Protection for trees is also available. No job to big or small References upon Request. Contact us today for a no cost or obligation estimate. We look forward to working with you on your Lightning Protection Project. Thank you. **WE ARE NOT ELECTRICIANS** **WE ONLY INSTALL LIGHTNING PROTECTION SYSTEMS **
"Great company, they were fast, friendly, & accommodating. I would definitely use them again."
The modern suburban and small town home of today has become an ideal lightning target. The home owner would do well to recognize lightning for the destructive force that it is and protect against this major life and fire hazard. Donohue's Lightning Rods is based in Missouri, near the factory where most of the residential and commercial lightning rod supplies are manufactured. Jim travels regularly to Texas, Louisiana, Arkansas, Missouri, Kansas, Montana, Wyoming, Colorado, and New York. Call today to find out when Jim will be in your area. For installations outside Missouri, Kansas, or Texas, Jim waits until there are a few customers lined up, thus being able to provide the same quality services at affordable prices. **WE DO NOT DO ELECTRICAL SERVICES.** (ONLY LIGHTNING RODS)
"The job was beautifully and professionally done. I have a zero scape yard and the gentleman was concerned about disturbing the gravel when putting the rod into the ground. WOW!!!!"
Debra D on June 2025
The modern suburban and small town home of today has become an ideal lightning target. The home owner would do well to recognize lightning for the destructive force that it is and protect against this major life and fire hazard. Donohue's Lightning Rods is based in Missouri, near the factory where most of the residential and commercial lightning rod supplies are manufactured. Jim travels regularly to Texas, Louisiana, Arkansas, Missouri, Kansas, Montana, Wyoming, Colorado, and New York. Call today to find out when Jim will be in your area. For installations outside Missouri, Kansas, or Texas, Jim waits until there are a few customers lined up, thus being able to provide the same quality services at affordable prices. **WE DO NOT DO ELECTRICAL SERVICES.** (ONLY LIGHTNING RODS)
"The job was beautifully and professionally done. I have a zero scape yard and the gentleman was concerned about disturbing the gravel when putting the rod into the ground. WOW!!!!"
Need an electrician to help you cut down costs on your next electricity bill? Let Mr. Electric of the North Country help you reach your goals. Whether it is installations, repairs or upgrades, Mr. Electric of the North Country has a solution for your home. With around the clock availability, our team offers several services that could benefit your home. Mr. Electric of the North Country can assist you with your every need.
"I had a whole-house generator installed by an electrical contractor.
It was wired incorrectly. I made an appointment with Mr. Electric of Queensbury, NY. They diagnosed the issue, ordered the parts, and installed them in a reasonable time. This was not their problem, but they treated it like it was. I am very impressed with their professionalism. Their employee Brian treated our home like it was his. When he had to enter our home, he put covers on his boots so he wouldn't track mud and snow into our home. He gave us an ETA for when he would come to do the work and explained the billing. If I need any electrical work done in the future, it will be done by Mr. Electric of Queensbury, NY."
Anthony B on April 2025
Need an electrician to help you cut down costs on your next electricity bill? Let Mr. Electric of the North Country help you reach your goals. Whether it is installations, repairs or upgrades, Mr. Electric of the North Country has a solution for your home. With around the clock availability, our team offers several services that could benefit your home. Mr. Electric of the North Country can assist you with your every need.
"I had a whole-house generator installed by an electrical contractor.
It was wired incorrectly. I made an appointment with Mr. Electric of Queensbury, NY. They diagnosed the issue, ordered the parts, and installed them in a reasonable time. This was not their problem, but they treated it like it was. I am very impressed with their professionalism. Their employee Brian treated our home like it was his. When he had to enter our home, he put covers on his boots so he wouldn't track mud and snow into our home. He gave us an ETA for when he would come to do the work and explained the billing. If I need any electrical work done in the future, it will be done by Mr. Electric of Queensbury, NY."
Sam Millington Electric is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are committed to customer service, which is why we take a hands on approach. When interacting with Sam Millington Electric, you'll notice that we're particularly focused on the principles of quality workmanship, timely completion, competitive pricing and integrity in all our business dealings. We combine knowledge and research with our extensive practical experience to ensure a specialized approach for your project needs. Contact us today for a fair and accurate estimate of your project. We look forward to adding you to our long and growing list of happy customers.
"They are Honest Dependable and Professional. I have quality work done . I have Recommend Sam to other People already . Thank you. Joyce"
Joyce O on November 2023
Sam Millington Electric is committed to excellence in every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are committed to customer service, which is why we take a hands on approach. When interacting with Sam Millington Electric, you'll notice that we're particularly focused on the principles of quality workmanship, timely completion, competitive pricing and integrity in all our business dealings. We combine knowledge and research with our extensive practical experience to ensure a specialized approach for your project needs. Contact us today for a fair and accurate estimate of your project. We look forward to adding you to our long and growing list of happy customers.
"They are Honest Dependable and Professional. I have quality work done . I have Recommend Sam to other People already . Thank you. Joyce"
We specialize in all types of construction including: interior pine, sheet rock, flooring, and remodeling. We also do all exterior work such as: exterior paint, roofing, decking, siding, soft, dock building, and so much more!. We have experience since 2014 in the construction field. . We strive to exceed expectations by delivering exceptional service, great quality work, and professionalism on every job. Read more below on all the services we offer and contact us with any questions or to schedule a free estimate today!
We specialize in all types of construction including: interior pine, sheet rock, flooring, and remodeling. We also do all exterior work such as: exterior paint, roofing, decking, siding, soft, dock building, and so much more!. We have experience since 2014 in the construction field. . We strive to exceed expectations by delivering exceptional service, great quality work, and professionalism on every job. Read more below on all the services we offer and contact us with any questions or to schedule a free estimate today!
Full Service Decking, Insulation and Window company - Decks & Porches -
"Dynasty Decking has my vote for best construction team. They are not only honest and trustworthy but kind and understanding. They worked with my budget and troubleshooted with me so that I got the best possible results. I recommend them to all my friends and family. They’re even certified through the state unlike a few of the other people who gave me outrageous quotes."
Marita K on March 2025
Full Service Decking, Insulation and Window company - Decks & Porches -
"Dynasty Decking has my vote for best construction team. They are not only honest and trustworthy but kind and understanding. They worked with my budget and troubleshooted with me so that I got the best possible results. I recommend them to all my friends and family. They’re even certified through the state unlike a few of the other people who gave me outrageous quotes."
Mr. Sharp specializes in tool sharpening services for your business and home. We sharpen knives, scissors, garden and workshop tools, beauty salon tools and more. We sharpen what others can't! We are a Marlborough, MA based company and provide our services in all 51 states in the United States. Our prices and turnaround times are extremely competitive. We strive to make your life better by providing excellent, fast and easy sharpening services. Our customers can bring their kits to our store at any time and drop them off in the drop box located near the store entrance. Also, if you are not in the area, we will send you a tracking label to ensure your beloved tools get to our store quickly and safely. Vladimir, the owner of Mr. Sharp, started sharpening knives when he worked as a chef in the kitchen for many years. He honed his skills before founding Mr. Sharp in October 2017. His main responsibility is to keep other chefs safe by sharpening kitchen tools. Later on, Mr. Sharp Company expanded its services! We now specialize in sharpening a wide variety of tools in many industries such as horticulture, cosmetology, woodworking, and more! We are proud to work with businesses and individual households. Today, Mr. Sharp strives to become one of the best sharpening services in the United States and continue to expand our sharpening skills to benefit every customer across the country.
Mr. Sharp specializes in tool sharpening services for your business and home. We sharpen knives, scissors, garden and workshop tools, beauty salon tools and more. We sharpen what others can't! We are a Marlborough, MA based company and provide our services in all 51 states in the United States. Our prices and turnaround times are extremely competitive. We strive to make your life better by providing excellent, fast and easy sharpening services. Our customers can bring their kits to our store at any time and drop them off in the drop box located near the store entrance. Also, if you are not in the area, we will send you a tracking label to ensure your beloved tools get to our store quickly and safely. Vladimir, the owner of Mr. Sharp, started sharpening knives when he worked as a chef in the kitchen for many years. He honed his skills before founding Mr. Sharp in October 2017. His main responsibility is to keep other chefs safe by sharpening kitchen tools. Later on, Mr. Sharp Company expanded its services! We now specialize in sharpening a wide variety of tools in many industries such as horticulture, cosmetology, woodworking, and more! We are proud to work with businesses and individual households. Today, Mr. Sharp strives to become one of the best sharpening services in the United States and continue to expand our sharpening skills to benefit every customer across the country.
...
Showing 1-10 of 114
FAQs for tv antenna installation projects in Bloomingdale, NY
The average cost to hire a handyman ranges from about $40 to $140 per hour. Average project cost ranges between $180 and $700, but the cost per hour and per project depends heavily on the type, size, and complexity of the project. The pro’s experience level and your location also factor into how much a handyman charges per hour or per project. You can also expect to pay higher rates or additional fees for emergency services, or around periods of high customer demand, like holidays.
If your TV antenna is good quality and was installed by a professional, you can expect it to last between 10 and 20 years without needing repair or replacement. This can vary based on your geographic location, weather conditions, and antenna location.
Yes, you should get a quote or an estimate from an electrician. Most electricians offer free estimates or quotes. When getting quotes, do your research and verify each electrician’s license. Get quotes from three different electricians to compare. If the prices or items listed appear different on the quotes, ask the electrician to clarify. Learning as much as you can about the electrical work you want done will help you get the most accurate estimate.
Qualified, licensed electricians will charge from $50 to $100 per hour. The cost to hire an electrician for emergency visits may range from $100 to $200 per hour because this urgent service usually takes place during off hours and may require an electrician to leave or reschedule jobs they’re currently working on. Scheduling work on holidays or during periods of high customer demand, like after a major storm, will also lead to higher rates or extra fees.
The cost to repair your TV antenna is around $200 for the average homeowner. However, charges could be as low as $60 or as high as $450. Factors such as multidirectional or unidirectional, indoor or outdoor, and amplified or non-amplified all play an essential role in determining the cost of your repair. For example, outdoor antennas cost more on average to repair than indoor ones, much like amplified antennas cost more to repair than unamplified ones.
The Bloomingdale, NY homeowners’ guide to tv antenna installation services
From average costs to expert advice, get all the answers you need to get your job done.
Before you hire a licensed electrical contractor, you should learn the cost to run electric from the road to your house so you can budget for the project.
If your electrical outlet is not working, you can try troubleshooting the outlet to fix it. Here are several causes and solutions for a faulty electrical outlet.
If your electrical panel is interrupting your home’s aesthetic, you can cover it with art, paint it, or try one of these other ways to hide an electrical panel.
Explore the pros and cons of a Level 1 charging station versus a Level 2 charging station when deciding the best way to charge your electric car at home.