Top-rated well and pump technicians.

Best well and pump technicians near Lovington, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Lovington, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Lovington, NM

*The Angi rating for Well And Pump Service companies in Lovington, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Lovington, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on May 04, 2026

Top-Rated Well and pump technicians in Lovington - Updated Nov 2026

Permian H2O Solutions, LLC
5.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Lovington, NM and surrounding areas

In business since 2015

Free estimates

Emergency services offered

Permian H2O Solutions, LLC is a licensed and insured water well drilling and service company. We pride ourselves on great service and pricing. Most service call are taken care of the same day. Permian H2O Solutions has been in business for 5 years serving the Permian Basin. We service a 150 mile around Midland/Odessa.

Recommended by100%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Lovington, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps FAQs, answered by experts

Reduced water pressure, strange noises, or air sputtering from faucets.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Most professionals recommend that a deep well pump shouldn’t run more than 10 hours consecutively before cycling off. Overworking the well pump beyond the recommended amount can prematurely wear out your pump and burn out the motor, which means replacing it more often than you otherwise should need to. Your well pump should also come with the manufacturer’s use and maintenance recommendations that are specific to the model.

Having a well means that a household’s water supply, including water that comes through faucets, showerheads, and appliances, is supplied through a private source rather than from a city. The well pulls fresh water from an underground water supply, such as an aquifer, and the well pump pushes the water from the well to your household.

If your well pump gets stuck in its casing, you may be able to free it loose by gently wiggling the line or by vibrations from tapping the line with a hammer. However, if your pump is stuck in a buildup of minerals around the casing, you’ll probably have to call in a well pump contractor to get it out. They’ll likely use a muriatic acid solution—a strong, corrosive acid—to break down the minerals and free the pump loose. 

To avoid a stuck pump in the future, experts recommend a professional well cleaning once every 10 years. 

The Lovington, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles