Top-rated well and pump technicians.

Get matched with top well and pump technicians in Hobbs, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Hobbs, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Hobbs, NM

*The Angi rating for Well And Pump Service companies in Hobbs, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Hobbs, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on March 04, 2025

Find Well and pump technicians in Hobbs

Permian H2O Solutions, LLC
5.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Hobbs, NM and surrounding areas

In business since 2015

Free estimates

Emergency services offered

Permian H2O Solutions, LLC is a licensed and insured water well drilling and service company. We pride ourselves on great service and pricing. Most service call are taken care of the same day. Permian H2O Solutions has been in business for 5 years serving the Permian Basin. We service a 150 mile around Midland/Odessa.

Recommended by100%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Hobbs, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Avatar for LoneStar Developers
LoneStar Developers
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Hobbs, NM and surrounding areas

Free estimates

Small jobs welcome

Credit card accepted

Need a reliable commercial or Residential construction crew? \n\nLonestar Developers has you covered. \n\nWe specialize in: \n• Framing \n• Plumbing \n• Electrical \n• Drywall \n• Acoustical Ceilings \n• Mud & Tape \n\nQuality work. Honest service. Built the Texas way. 🤘 \n\n📩 Message us today for quotes or project inquiries.

Request Quote
Wells and Pumps questions, answered by experts

For the most part, choosing between 30/50 psi and 40/60 psi is based on your water-pressure preference. However, it can also depend a little bit on your house—if you have older plumbing, a lower water pressure can be easier on the pipes (and a bit more gentle on your well pump). 

The lower 30/50 pressure is usually enough for a single-story home, but you may want 40/60 if you have multiple stories, as the extra pressure helps water flow smoothly up to the second floor.

If you’re going away on vacation or leaving your home for a long time, it’s a good idea to switch off your well pump and pressure tank before you go. This way you can prevent any damage from unexpected leaks that may occur or unforeseen electrical issues while you’re away.

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

The average three to four-bedroom home typically uses a well pump rated for 8 to 12 gallons per minute (GPM). To find the most accurate size for your specific needs, a common rule of thumb is to count the number of water fixtures and appliances in your home and aim for that number in GPM. This calculation allows for about one gallon of water per minute per fixture. Because estimating the correct size can be challenging, it's best to have a professional technician make the final determination. A professional can ensure your pump provides sufficient water for your home, especially during peak usage hours.

Though sprinkler systems can have varying issues, there are a few common ways to know if the cause is your pump. Signs include cracking or visible damage, leaking from the pump, a pump that won’t turn on, and loud noises coming from your pump. Low or irregular pressure could also point to a pump problem, but there are other causes.

The Hobbs, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles