Top-rated contractors.

Get matched with top contractors in Casselton, ND

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Casselton, ND?

Select your specific project to find the pro for you.

Find Contractors in Casselton

Avatar for Swenson Contracting
Swenson Contracting
4.9(
7
)
Major Home Repairs (General Contractor)

Serving Casselton, ND and surrounding areas

In business since 2015

Free estimates

"Professionals with talent and skill! I hired them to drywall/tape/texture and spray foam insulate my basement after a flooding issue. Their attention to detail, finished product and professionalism was top notch. They not only did a fabulous job, they also cleaned up after themselves everyday! I'd definitely hire them again for future projects."
Faucet side tub wall
Toilet and faucet wall
Inside shower
Vanity
Tub surround

+37

Response time2 days
Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Casselton, ND and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Casselton, ND and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Avatar for Merls Handyman
Merls Handyman
5.0(
2
)
Major Home Repairs (General Contractor)

Serving Casselton, ND and surrounding areas

In business since 2023

Free estimates

Emergency services offered

Merls Handyman is reliable, easy to work with, and dedicated to getting your home back into shape. I have over 15 years of general experience and always have the best attitude about my work. We offer free estimates and would love to hear of your upcoming project. Call or click for an estimate today

Bathroom remodel
Housecleaning Project
Shed build
Trailer painting
Landscaping Project

+64

Recommended by100%of homeowners
Showing 1-10 of 31
Unfinished Carpentry questions, answered by experts

Yes, you will need a jack for a rim joist replacement. To prevent sagging and facilitate the removal of load-bearing wood, you’ll need to relieve the pressure from this joint before beginning work. 

Due to hydraulics and other specialized equipment, a sill plate and rim joist replacement are not typically a DIY project. Hiring a professional structural engineer and experienced contractors is the best approach to replacing rotted sill plates and rim joists.

Most load-bearing walls are exterior, though they can also be interior.

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

While some highly experienced homeowners can frame a house independently, it is not advisable. You will need ample carpentry experience, a team of helpers, and professionals to sign off on your work to meet local building codes. For the safest outcome, we recommend buying or building a house with the guidance of professionals.

Joists do distribute their load to beams, but they don’t sit on top of the beams. Instead, home builders nail or screw the joists directly to the beams such that the end of the joist butts up against the edge of the beam. Beams can sit on other beams for support, but you’ll never see a joist sitting on top of a beam or another joist.

The Casselton, ND homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.