Get matched with top structural engineers in Spring Lake, MI

Q: How high can you build a single brick wall?

• <div><p>A freestanding brick wall that's only one brick thick can usually stand six to eight feet high. If you need a higher wall, it should be at least two bricks thick for adequate stability, and it might require a footing to support the added weight. Additionally, some areas have regulations and codes dictating how high a brick wall can be, so check with local code enforcers to ensure your proposed wall complies with any regulations.</p></div>

Q: How do contractors cut a doorway in a concrete block wall?

• <div><p>First, most contractors will have a structural engineer create a report and plan for your project to ensure it&rsquo;s safe to cut into the load-bearing wall. The contractor will then excavate around the wall, if necessary, measure the opening&mdash;allowing for additional space to fit and level the door, and then cut the doorway out. They will likely install a steel lintel as a header over the door for support. Once the doorway is cut out, they&rsquo;ll demolish the concrete using sledge hammers and masonry chisels, clean up the surrounding concrete, and seal around the door with masonry mortar. </p></div>

Q: What are the disadvantages of a cathedral ceiling?

• <div><p>Cathedral ceilings make a statement in your home, but at the cost of your attic space. Normal attics are wide open, which allows warm air to move around and exit your home. Because of this, cathedral ceilings make your home less energy efficient and put your ceiling at risk of venting issues if you&rsquo;re not careful. They also reduce your attic storage space, potentially cause an echo, and even make it harder to change a light bulb. </p></div>

Q: Are all exterior walls load-bearing?

• <div><p>It's safe to assume that all exterior walls are load-bearing, or at least have load-bearing characteristics. Some older homes feature porches or bump-outs that don't rest on the home's foundation. However, they still must carry the weight of the roof section they support. Walls containing floor-to-ceiling glass or other non-structural elements must use post and beam configurations to meet load-bearing criteria. </p></div>

Q: Can a one-story house have a load-bearing wall?

• <div><p>Yes, a one-story house can have a load-bearing wall. The load-bearing walls in a single-story home are usually the exterior walls. If the house has a basement with exposed walls, the arrangement of the beams can help indicate what walls are load-bearing.</p></div>

Enter your zip and get matched with up to 5 pros

Need a pro for your structural engineering project in Spring Lake, MI?

Select your specific project to find the pro for you.

Verified Reviews for Structural Engineering pros in Spring Lake, MI

*The Angi rating for Structural Engineering companies in Spring Lake, MI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Structural Engineering needs.

*The HomeAdvisor rating for Structural Engineering companies in Spring Lake, MI is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Structural Engineering needs.

Last update on May 06, 2025

Find Structural engineers in Spring Lake

Robert Cowles PE

5.0(

)

Serving Spring Lake, MI and surrounding areas

Approved

In business since 2004

Offers commercial services

"Robert responded quickly to my request. He provided me with the services I needed in a timely fashion. I would recommend Robert Cowles PE for your project."

Response time1 day

12 neighbors recently requested a quote

Request Quote

Foundation Specialist, LLC

4.2(

)

Serving Spring Lake, MI and surrounding areas

In business since 2012

Free estimates

Emergency services offered

"I'm selling a home in Holland. The appraiser noticed a crack in the poured concrete foundation and asked for further investigation by a licensed foundation expert. Bryan Foster showed up promptly, provided a written report that confirmed no settlement, bowing or water intrusion, and charged a fair price. I didn't need or ask for an estimate, but Mr. Foster provided one free. I appreciate that the estimate was separate from the inspection report."

Recommended by85%of homeowners

Request Quote

Structural Engineering questions, answered by experts

A freestanding brick wall that's only one brick thick can usually stand six to eight feet high. If you need a higher wall, it should be at least two bricks thick for adequate stability, and it might require a footing to support the added weight. Additionally, some areas have regulations and codes dictating how high a brick wall can be, so check with local code enforcers to ensure your proposed wall complies with any regulations.

First, most contractors will have a structural engineer create a report and plan for your project to ensure it’s safe to cut into the load-bearing wall. The contractor will then excavate around the wall, if necessary, measure the opening—allowing for additional space to fit and level the door, and then cut the doorway out. They will likely install a steel lintel as a header over the door for support. Once the doorway is cut out, they’ll demolish the concrete using sledge hammers and masonry chisels, clean up the surrounding concrete, and seal around the door with masonry mortar.

Cathedral ceilings make a statement in your home, but at the cost of your attic space. Normal attics are wide open, which allows warm air to move around and exit your home. Because of this, cathedral ceilings make your home less energy efficient and put your ceiling at risk of venting issues if you’re not careful. They also reduce your attic storage space, potentially cause an echo, and even make it harder to change a light bulb.

It's safe to assume that all exterior walls are load-bearing, or at least have load-bearing characteristics. Some older homes feature porches or bump-outs that don't rest on the home's foundation. However, they still must carry the weight of the roof section they support. Walls containing floor-to-ceiling glass or other non-structural elements must use post and beam configurations to meet load-bearing criteria.

Yes, a one-story house can have a load-bearing wall. The load-bearing walls in a single-story home are usually the exterior walls. If the house has a basement with exposed walls, the arrangement of the beams can help indicate what walls are load-bearing.

The Spring Lake, MI homeowners’ guide to structural engineering services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles

Lyle Hendriks
•
May 5, 2026May 5, 2026
How Much Does Beam Installation Cost [2026 Data]
Beam installation costs are an important consideration if you’re building a home or doing renovations. Learn about average costs and factors in this guide.
Haley Nothstein
•
May 30, 2026May 30, 2026
How Much Does It Cost to Replace a Main House Support Beam? [2026 Data]
A damaged main support beam can cause serious structural damage to your house. Learn how much it costs to replace a main house support beam.
Alison Kasch
•
Apr 4, 2026Apr 4, 2026
How Much Does It Cost to Remove a Load-Bearing Wall? [2026 Data]
Do you have a load-bearing wall standing between you and your projects that you want to remove? Learn about the cost of removing a load-bearing wall.
Rachel Hoffman
•
May 2, 2026May 2, 2026
Structural Steel Beam vs. Wood Beam: Which Is Right for You?
Structural steel and wood beams ensure your house is structurally sound. Learn the difference between steel and wood beams and how to choose the right one.
Kate Fann
•
Mar 19, 2026Mar 19, 2026
Who Do You Hire to Knock Down a Wall?
Looking to open up your living space and need to remove a wall? Learn who to hire to knock down a wall, whether it's load-bearing or non-load-bearing.
Dan Simms
•
Apr 9, 2026Apr 9, 2026
What Is a Structural Engineer and Do You Need One?
Learn what a structural engineer is, what they do, when you might need to hire one for your home project, and how much they charge.