Top-rated contractors.

Get matched with top contractors in Shelby, MI

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Shelby, MI?

Select your specific project to find the pro for you.

Find Contractors in Shelby

Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Shelby, MI and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Shelby, MI and surrounding areas

In business since 2006

Credit card accepted

"Once I sent her all the measurements, it took her a little while to get the options back to me.  Overall, they're good designs.  However, they're very simplistic and give general ideas for space planning.  I was hoping to have a better idea for sizes of furniture for the space and some variations on staging.  
Jill was very responsive when I did have a question.  I'm not sure how helpful it is to have a virtual design done.  If we lived in similar cities, I'd probably use her again for help with additional designs.
"
Recommended by55%of homeowners
Joe S Kutchinski builders
New to Angi
Major Home Repairs (General Contractor)

Serving Shelby, MI and surrounding areas

Free estimates

Warranties offered

Small jobs welcome

I was born and raised in lake county, october nineteen sixty four. My father was a contractor in the 60s through 2015. I also had an uncle that was a contractor here in Lake County and an uncle. That is a contractor up in Traverse City. I worked with all of them from the 70s on. Mostly worked for my dad until 1988 when I got my residential builders license. Working here in Lake County, you had to learn to do all of the jobs yourself. You had to learn to do concrete, foundations, lay blocks, framing, build rafters, do roofing shingles or metal roofing. Set windows do siding. Build additions, garages, pole barn, porches, decks, sheds. Do installation, drywall, finished trim.\nFlooring ceramic, tile hardwood floors, laminate flooring. Do trim work ect. I do have subcontractors that I work with. I did the remodel job on the dial a ride building in lake county. I did the Idlewild welcome signs on US 10. I worked with Habitat for Humanity.\nFor the last 8 years. Hopefully hope we can do busi\n\n

Showing 1-10 of 16
Unfinished Carpentry questions, answered by experts

A-frame homes are on the smaller side. While there’s no set square footage amount it has to be, it will usually come in around 1,000 square feet or smaller.

One of the most common house framing basics for decades has been using wood for the framing work. However, some framing contractors now suggest using steel frames. Steel is lightweight, resistant to fire, and resistant to moisture, all of which are areas where wood framing could cause problems. However, steel framing is more expensive than wood and limits your ability to insulate the home.

Most Cape Cod houses are two stories tall at the peak, although they’re considered one-and-a-half stories tall because the steep roof pitch cuts off a portion of the living space on the second story. Unless you raise the roof on your Cape Cod house to add a dormer, the interior rooms upstairs will lose some usable living space to the sloped ceilings.

When hanging a door frame, it’s recommended that you use screws, not nails. Screws are more secure, easier to tighten, and easier to remove if you need to adjust the frame. On average, the cost to replace a door frame is about $400, but you can save on labor costs if you’re confident in your ability to DIY the project. 

There are approximately 5.33 board feet in a 2x4. You can use the board foot calculator in this article to easily find the answer. A 2x4 is 2 inches of thickness by 4 inches of width, so you need to find the length, with 8 feet being the most common. You’d use the calculator here to multiply 2 times 4 times 8, and then divide by 12, arriving at a total of 5.33 board feet. 

The Shelby, MI homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.