Top-rated buffing and polishing pros.

Get matched with top buffing and polishing pros in Laporte, CO

Enter your zip and get matched with up to 5 pros

Need a pro for your buffing and polishing project in Laporte, CO?

Select your specific project to find the pro for you.

Find Buffing and polishing pros in Laporte

Avatar for Daily's Handy Essentials
Daily's Handy Essentials
New to Angi
Clean & Polish Flooring - For Business

Serving Laporte, CO and surrounding areas

Approved

Free estimates

Emergency services offered

Warranties offered

Hi neighbors! I’m a local handyman offering reliable, flat-rate services right here in the area. Whether you need a TV mounted, general repairs handled, flooring installations done, or winter weatherproofing, I’m happy to help keep your home running smoothly—reach out today to get your project checked off the list!

JD Cleaning Service, LLC - Home Facebook
5.0(
4
)
Clean & Polish Flooring - For Business

Serving Laporte, CO and surrounding areas

In business since 2014

Free estimates

Offers commercial services

"Joe did an awesome job and if you are needing quality carpet cleaning then I would highly recommend Joe. He is respectful and on time and listens to your needs and makes sure you are completely satisfied with his work. My carpets look great and smell great. Also if you have pets and they have accidents Joe has been the best to remove any smells out of carpet."
CLEANING STAIRS
CLEANING CARPET
CARPET
THE VAN
CARPET CLEANING

+1

Response time3 hrs
Recommended by100%of homeowners
Avatar for Omni Services
Omni Services
4.0(
104
)
Clean & Polish Flooring - For Business

Serving Laporte, CO and surrounding areas

In business since 2006

Free estimates

Credit card accepted

"The bonus room, above the garage, was the coldest place in the house in winter, and the hottest in summer.   Air was coming in through the trim/baseboard, and the sub-floor itself was very cold in winter.  The goal Omni Services (OS) and I agreed to was to provide a year-round comfortable space.  As a consumer, I wanted the room to be "air tight" but OS could not guarantee that.
In preparation for the bonus room work, I removed the trim, carpet and pad for later re-use, and cut out (as best I could) some agreed-on 4x8 and 4x12 sections of the existing drywall, so we could see what was going on inside the walls and ceiling.  The scope-of-work document had Omni Services (OS) removing the sub-floor as well, to check out the insulation beneath it, but ultimately OS didn't deem that necessary, as they found a different way to add insulation. [So in hindsight I removed the carpet and pad unnecessarily.]
OS determined:
  a. the ceiling insulation was wrong for the space (R30 was crammed in, R19 should have been used)
  b. the roof above the bonus room (2x8 boards between the ceiling and the roof) had insufficient  ventilation
  c. there was insufficient insulation in the garage attic (adjacent to the bonus room) that was a continuation of the roof above the bonus room
 
What OS did for the ceiling:
  a. removed the R30 from most of the ceiling
  b. installed "proper vent"  (a way for air to flow between the lower and upper parts of the roof) where the R30 had been
  c. replaced the R30 (that was removed) with R19
  d. added some exterior ventilation (around the gutters and in the garage attic) to allow more air into the "proper vent"
  NOTE:  I had a roofing company install ridge-cap ventilation above the bonus room; OS's work was pointless without that
 
What OS did for the garage attic adjacent to the bonus room:
  a. install foam board insulation over the sloping area (continuation of the bonus room roof, into the attic)
  b. spray in more insulation
What OS did for the sub-floor:
  a. accessed the underside of the sub-floor from either the garage attic or the limited space between the bonus room walls and the ceiling (which continued downward into the garage attic)
  b. sprayed in more insulation
THE BAD: Once the drywall was replaced, taped, etc., and before the trim was put back on, there was still significant airflow into the room, where the drywall met the sub-floor.  I had not expected this, nor had OS.  I "fixed" this by using a combination of low-expanding foam from a can, leftover fiberglass insulation, and drywall mud.  Air was also coming in from the drywall holes cut for the electrical boxes, but styrofoam covers fixed that.
What OS did for the main attic stairs (accessible from the bonus room):
  a. manufactured a cover using leftover foam board and other materials
  b. installed the cover above the pull-down attic stairs
  c.  sprayed in more insulation in the attic, in the area around the new cover
What OS did for the doors:
After I removed the trim from the French doors, OS replaced one of the doors, which had warped.  I painted the door, then OS reinstalled the trim.
BOTTOM LINE:  We do not yet know whether the bonus-room goal was met.   We won't know until we have a string of really hot days, and another string of really cold days.


"
Recommended by81%of homeowners
Avatar for Rushold Enterprises
Rushold Enterprises
4.8(
5
)
Clean & Polish Flooring - For Business

Serving Laporte, CO and surrounding areas

In business since 1994

Free estimates

"Owner and staff were courteous, professional, and prompt. Received estimate on Wednesday and work done Friday. The Job took no time at all. Overall I am very satisfied with the results, and would definitely hire them again."
Recommended by100%of homeowners
Showing 1-10 of 35
Buffing and Polishing questions, answered by experts

To maintain tile and grout, clean the surfaces regularly with mild, non-abrasive cleaners and wipe up spills promptly to prevent buildup. It is also important to reseal the grout every 1-2 years to maintain its durability.

Like most stones, limestone should be sealed. Its porous nature makes it prone to staining from spills, and the iron in the stone can cause it to turn yellow when exposed to moisture or harsh chemicals. Proper sealing can help prevent these problems and protect the stone's appearance.

Costs depend on tile material, damage severity, labor, and whether refinishing is required.

To remove cloudiness from marble, use equal parts baking soda and water to form a paste. Apply it to the surface, allow it to sit for at least two hours, then wipe with a microfiber cloth. Another option is adding a couple of dish soap drops to warm water and wiping the surface after you’ve applied it to the surface. You may also consider using a liquid stone cleaner.

The answer to this question depends on how large the room is and how much experience you have stripping and waxing floors. It will take at least 24 hours to strip the floors, then you must allow time for drying, waxing, waiting for them to cure, and, finally, buffing them. Since you likely will not be working for the full 24 hours, it is safe to say that this is a two- or three-day job.

The Laporte, CO homeowners’ guide to buffing and polishing services

From average costs to expert advice, get all the answers you need to get your job done.