"Keith Williams is the definition of professionalism. Not only is his work incredible, but he is extremely personable. We replaced a wooden gate and section of fence with a wrought iron gate. Keith discussed all possible options that might work well with our needs. He did not try to up-sell any features; if anything, he mentioned some aspects that might save us money. We ended up choosing a single 10-foot gate with small sections on either side. The project took 3 days, but the first day was mostly setting the posts and allowing the concrete to set. Keith and his assistant were always punctual. I highly recommend him for your wrought iron fence and gate needs."
"Everything went great! Mr. Strickland kept me informed throughout project with scheduling, install process and concrete maintenance. Would definitely recommend!"
"When I arrived home from work, the existing driveway had been removed. A new section had been poured. The next section did not have the proper prep work performed. I had them prepare the ground properly on this section. I was told that the section that was already poured had been prepared properly. The third cement truck load was late in arriving by several hours. As a result, that section did not match (color) the shade of the previous two sections. The finish we had agreed upon was a washed limestone with a red sand finish. The third load was a lot lighter than the previous two loads. Mr. Evans said that the shades of the two pours would match in a couple of years. A representative from Sardis Ready Mix (the concrete company) was called out and offered to replace that load of concrete at no cost. However, Mr. Evans was reluctant to tear out what he had just poured and replace it. In the end he did so. Some of the lines seperating the sections are not straight and the finish has a few low spots & rough spots. Also, dirt from the prep work was piled in the yard, killing the grass and clogging a rain water run off drain. The concrete from the section he replaced was piled in the yard destroying plants and grass. We now have hired a lanscaper to come repair our yard."
Since 2014, Millennium Contracting has offered professional Home Improvement Services. We provide a full range of Interior and Exterior Residential Contracting services such as; Carpentry and Framing, Remodeling, Additions, Drywall, Painting, Flooring, Windows, Doors, and more! We are dedicated to customer satisfaction and fully stand behind our work. We offer free consultations and estimates, and will work with you to explain your options, and create a customized solution for your Home Improvement needs. Get the job done correctly the first time, call Millennium Contracting today!
"Victor and crew arrived around 9am and immediately began to work moving and covering furniture and patching walls. They were very courteous, professional and worked steadily until job was done. I don't think they ever took a break. There were three men her for nine hours. The price was incredibly reasonable. The finished job was awesome. They didn't cut any corners. If the walls needed sanding then they sanded, if another coat was needed then they gave it another coat. I would highly recommend this company to anyone. I give them five stars!!!!!!"
"It went well. Ron showed up on time to give an estimate. The following week, he and his crew got to work. He even put the cat up (so that she wouldn't get out) when I wasn't able to do so. There were a few places that I've asked that the crew go back over, i.e., cutting in lines aren't straight. But Ron had no problem with that and has said several times that he wants to make sure that I'm happy. The paint job that was done in my dining room was totally his idea, stripes with the same color only different finishes, flat and high gloss. It looks GREAT!!!"
Have you seen black streaks on the side of your home. \nAre you embarrassed of having a dirty home. \nIs your driveway looking old and no longer new and fresh.\nCall us today for a free estimate.\nWe offer to clean your home, driveway, gutters, fences, decks and more...\n\nwe also do handyman work , remodel
Welding is the process of using extreme heat—and, sometimes, pressure—to attach two pieces of metal. In contrast, metal fabrication is a more involved process that can include welding, sheet metal work, bending, and other forms of metal manipulation. Metal fabrication is a large-scale project that may or may not involve welding, while welding is more often a step in larger fabrication projects.
Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.
Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.
Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.
Welders use a variety of methods in their trade. Different types of welding are better suited for different purposes and contexts. For example, stick welding is a versatile form suitable for most metals and alloys.
The most common types of welding include:
Stick welding: $100–$1,000
Metal Inert Gas (MIG) welding: $250 and up
Tungsten Inert Gas (TIG) welding: $250 and up
Gas welding: $150 and up
Forge welding: $15–$25 per hour
The Earle, AR homeowners’ guide to concrete cutting services
From average costs to expert advice, get all the answers you need to get your job done.
