Top-rated concrete cutting pros.

Best concrete cutting pros near Marion, AR

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Marion, AR?

Select your specific project to find the pro for you.

Top-Rated Concrete cutting pros in Marion - Updated Nov 2026

Avatar for Decks Etc
Decks Etc
4.3(
129
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Marion, AR and surrounding areas

In business since 1985

Free estimates

Credit card accepted

" The progress in the extreme heat was amazing,
The 2 Deck, Etc men were very fast in tearing the old section out and placinng the new posts in concrete.
 
The following day was spent on the placement of the newly cut boards and the header.
Cleanup of the yard was quickly taken care of.
"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+6

Recommended by89%of homeowners
S Evans Construction Co
3.9(
12
)
Concrete Flatwork - Repair & Resurface

Serving Marion, AR and surrounding areas

"When I arrived home from work, the existing driveway had been removed. A new section had been poured. The next section did not have the proper prep work performed. I had them prepare the ground properly on this section. I was told that the section that was already poured had been prepared properly. The third cement truck load was late in arriving by several hours. As a result, that section did not match (color) the shade of the previous two sections. The finish we had agreed upon was a washed limestone with a red sand finish. The third load was a lot lighter than the previous two loads. Mr. Evans said that the shades of the two pours would match in a couple of years. A representative from Sardis Ready Mix (the concrete company) was called out and offered to replace that load of concrete at no cost. However, Mr. Evans was reluctant to tear out what he had just poured and replace it. In the end he did so. Some of the lines seperating the sections are not straight and the finish has a few low spots & rough spots. Also, dirt from the prep work was piled in the yard, killing the grass and clogging a rain water run off drain. The concrete from the section he replaced was piled in the yard destroying plants and grass. We now have hired a lanscaper to come repair our yard."
Recommended by66%of homeowners
Avatar for Paintmaster Plus LLC
Paintmaster Plus LLC
4.3(
121
)
Concrete Flatwork - Repair & Resurface

Serving Marion, AR and surrounding areas

In business since 1993

Free estimates

"It went wonderful. They were superior. They were on-time, they even stayed over the eight hours to finish up the little bit of painting that needed being done. They were very polite and professional. These people were above and beyond."
Additional Photos
Additional Photos
Before
After
Additional Photos

+2

Recommended by98%of homeowners
PEGASUS PAINTING/CONSTRUCTION
4.6(
9
)
Concrete Flatwork - Repair & Resurface

Serving Marion, AR and surrounding areas

In business since 1999

Emergency services offered

"It went well. Ron showed up on time to give an estimate. The following week, he and his crew got to work. He even put the cat up (so that she wouldn't get out) when I wasn't able to do so. There were a few places that I've asked that the crew go back over, i.e., cutting in lines aren't straight. But Ron had no problem with that and has said several times that he wants to make sure that I'm happy. The paint job that was done in my dining room was totally his idea, stripes with the same color only different finishes, flat and high gloss. It looks GREAT!!!"
Recommended by87%of homeowners
Showing 1-10 of 34
Concrete Cutting FAQs, answered by experts

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Costs depend on unit complexity, labor, wall mounting needs, and additional accessories like floating shelves.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

The Marion, AR homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.