Top-rated concrete driveway pros.

Best concrete driveway pros near Earle, AR

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete driveway service project in Earle, AR?

Select your specific project to find the pro for you.

Top-Rated Concrete driveway pros in Earle - Updated Nov 2026

Avatar for J. Diaz Construction
J. Diaz Construction
4.7(
104
)
Concrete Driveways & Floors - InstallConcrete Driveways - InstallConcrete Floors - Install

Serving Earle, AR and surrounding areas

In business since 2008

Free estimates

Warranties offered

"They were prompt, professional, proficient and kind! Very reasonable quote!They did more than I asked. My home and garage looks beautiful! The day they finished my roof they cleaned up ! Wonderful company! I highly recommend J.Diaz Construction."
Response time11 hrs
Recommended by95%of homeowners
S Evans Construction Co
3.9(
12
)
Asphalt Paving - InstallConcrete Driveways & Floors - InstallConcrete Driveways & Floors - Install- For Business+5 more

Serving Earle, AR and surrounding areas

"When I arrived home from work, the existing driveway had been removed. A new section had been poured. The next section did not have the proper prep work performed. I had them prepare the ground properly on this section. I was told that the section that was already poured had been prepared properly. The third cement truck load was late in arriving by several hours. As a result, that section did not match (color) the shade of the previous two sections. The finish we had agreed upon was a washed limestone with a red sand finish. The third load was a lot lighter than the previous two loads. Mr. Evans said that the shades of the two pours would match in a couple of years. A representative from Sardis Ready Mix (the concrete company) was called out and offered to replace that load of concrete at no cost. However, Mr. Evans was reluctant to tear out what he had just poured and replace it. In the end he did so. Some of the lines seperating the sections are not straight and the finish has a few low spots & rough spots. Also, dirt from the prep work was piled in the yard, killing the grass and clogging a rain water run off drain. The concrete from the section he replaced was piled in the yard destroying plants and grass. We now have hired a lanscaper to come repair our yard."
Recommended by66%of homeowners
Pita's Painting
5.0(
7
)
Concrete Flatwork - Repair & ResurfaceConcrete Flatwork - Repair & Resurface- For BusinessConcrete Floors - Install+1 more

Serving Earle, AR and surrounding areas

In business since 2002

"I cannot reccomend this company enough. I had a HUGE project for them and they made it happen in the time frame they estimated. We needed our entire home painted, ceilings, walls, all molding and baseboards. Truly went above and beyond! They even stayed and continued working without power in our house. Reasonably priced with quality work. Such a pleasure to work with them, fantastic attitudes and so easy to communicate with. They will be my painters from here on out. I am so grateful to have found them."
Recommended by100%of homeowners
Showing 1-10 of 31
Concrete Driveways FAQs, answered by experts

You don't technically need to seal your driveway after pressure washing, but doing so will help keep your driveway clean for longer. The best driveway sealer depends on the type of driveway you have. To seal asphalt, consider an asphalt emulsion sealer, fast-drying sealer, or latex acrylic sealer. Concrete driveways commonly use acrylic sealers or penetrating sealers.

Pressure washers are better for residential use. Power washers are best suited for cleaning very hard surfaces (like concrete and cement) and removing tough stains or tacked-on grime. Meanwhile, pressure washers have more uses. For example, you can use one to deep clean a wooden fence, spray down your vinyl siding, or clear out your gutters.

Yes, you can and should pressure wash a stamped concrete driveway, as well as other stamped concrete around your yard on the patio or walkways. While the stamping pattern can handle the pressure of the water, it's still best to use a gentle solution to avoid breaking down the concrete or affecting any additional stain coloring added to the design.

You should wait until your pavers have completely dried and cured before pressure washing them. Wait at least three to five days, though some sealants may need up to an entire week. Rushing that timeline can mess with the finish, weaken the seal, or leave streaks that are tough to fix. Once the sealant has fully set, stick to a gentle approach. Keep the pressure under 1,500 PSI and hold the nozzle at least two feet from the surface. Anything stronger or closer can blast the joint sand loose or wear down the sealant you just applied.

Yes. You can pressure wash pavers. However, you risk damaging them if you use too much pressure or get too close. Use a PSI of 1,500 and spray the water at least 24 inches away from the surface.

The Earle, AR homeowners’ guide to concrete driveway services

From average costs to expert advice, get all the answers you need to get your job done.