Top-rated electricians.

Get matched with top electricians in Port Edwards, WI

Enter your zip and get matched with up to 5 pros

Need a pro for your electrical service project in Port Edwards, WI?

Select your specific project to find the pro for you.

TRUSTED BY PORT EDWARDS, WI HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon38
    Verified electrical services reviews

Find Electricians in Port Edwards

Ingenuitive Enterprises LLC
New to Angi
Telephone Jacks and Wiring - InstallTelephone Jacks and Wiring - Install - For BusinessTelephone System - Install or Upgrade+3 more

Serving Port Edwards, WI and surrounding areas

Approved

Free estimates

Welcome: To a business that holds dear to "old school" morals and values, and also keeps a budget in mind. Here at Ingenuitive Enterprises, our goal is to provide the best, most honest service in the industry, while still delivering surprisingly great quality results. This business was built on the principle that if the repair is executed correctly the first time, then it is done right.\n*Thank You* for your interest, and for considering Ingenuitive Enterprises for your home and/or business repair/maintenance/remodel needs and desires!! We look forward to the opportunity to show you why we are: "The RIGHT Handyman Solution, FOR YOU, Every Time."

Luke Electrical
4.6(
17
)
Ceiling Fan - InstallElectrical Switches, Outlets & Fixtures - Install or RepairElectrical Switches, Outlets & Fixtures - Install or Repair - For Business+10 more

Serving Port Edwards, WI and surrounding areas

In business since 2006

Free estimates

Credit card accepted

"We were hit by a lightening, and he came right over to help us with our electrical issues. He replaced the fuse box for us, and did an excellent job. Very easy to talk to, and explained everything, thorough. I would hire them again."
Response time4 days
Response rate100%
Recommended by93%of homeowners
Ray's Electric Service, LLC
5.0(
1
)
Ceiling Fan - InstallCeiling Fan - RepairElectric Vehicle Charging Station Installation - Materials Not Provided+13 more

Serving Port Edwards, WI and surrounding areas

In business since 1936

Free estimates

With several years of experience, we work hard to bring each customer the best possible service and quality available. We look forward to working with you on your next project. We welcome your questions and thank you for your interest.

Response time2 days
Response rate100%
Recommended by100%of homeowners
Showing 1-10 of 25
Electrical questions, answered by experts

Natural gas and electricity rates vary significantly based on location, and pricing can change over time, too. It’s possible that in locations where natural gas is particularly inexpensive, it will cost less than grid-based electricity will. However, you should also factor in the generator’s initial costs and maintenance needs, as well as its noise level and if it can comfortably power all your home appliances.

Yes, it's possible to have electrical receptacles and overhead lights on the same circuit. The reason is that lights typically use much less power than large appliances, so combining them won't overload your circuit. By doing this, you can distribute the power consumption throughout the breakers in your panel more efficiently, which can be helpful if you have a lot of different electrical devices in your home.

The standard copper wire gauge to use with any 30-amp circuit is a 10-gauge wire. The National Electric Code specifies a 10-gauge wire with appliances like water heaters running on 30 amps. If you try to use a smaller gauge wire, such as a 12 gauge, with a 30-amp breaker, you run the risk of the wire overheating and melting or causing a fire. Because of the safety hazards, the gauge of the wire is not an area to try to cut costs when connecting a 30-amp breaker to a water heater.

Yes, you can use a 3/0 AWG wire for a 200 amp service, but only if it is made of copper, as 3/0 copper wire has an allowable ampacity of 225 amps. If you are using aluminum or aluminum copper-clad wire, you need to use at least 4/0 AWG.

It’s possible to distinguish a positive black wire from a negative black wire if you know what type of circuit the wires are in. If it’s an alternating current (AC), then black wires are positive. If it’s a direct current (DC), then black wires are negative. 

Sometimes, a circuit has two black wires. In that case, the positive black wire will be solid black while the negative black wire will have a white stripe on it. If you’re still unsure, you can use a multimeter to check.

The Port Edwards, WI homeowners’ guide to electrical services

From average costs to expert advice, get all the answers you need to get your job done.