Top-rated well and pump technicians.

Get matched with top well and pump technicians in Moab, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Moab, UT?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Moab, UT

*The Angi rating for Well And Pump Service companies in Moab, UT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Moab, UT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on March 25, 2025

Find Well and pump technicians in Moab

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Moab, UT and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Avatar for J & K Mechanical
J & K Mechanical
5.0(
1
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Moab, UT and surrounding areas

In business since 2018

Free estimates

Emergency services offered

J & K Mechanical LLC is committed to excellence every aspect of our business. We uphold a standard of integrity bound by fairness, honesty, and personal responsibility. Our distinction is the quality of service we bring to our customers. Accurate knowledge of our trade combined with ability is what makes us true professionals. Above all, we are watchful of our customers' interests and make their concerns the basis of our business.

Recommended by100%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Here are some signs of a bad well pump that a pro should look at: 

  • If your well pump isn’t pumping water, you could have a leak or malfunctioning pump on your hands. 

  • If your water pump runs nonstop, there might be a leak or problem with the pressure tank, which can cause the pump to fail. 

  • Low water pressure can happen because of your pressure tank, low-water levels, or a wrong-sized pump. 

  • Dirt or sediment in your water can be a problem with a powerful pump, damaged pump filter, or the pump’s location.

You should have your well inspected once per year. You should also have a well inspection done when you’re buying a house with a private well, when the well cap is opened, when the septic tank is repaired, or when there is flooding.

During your annual visit, a pro will make sure that everything is working correctly and check for certain contaminants, including total coliform. Every other year, they’ll look for things like metals and nitrates, and every five years, they’ll test for pesticides.

Wells typically replenish at a rate of about five gallons per minute, but several variables can influence how quickly they refill. A deep well will take more time to replenish than a shallow one. The replenishment rate can be slowed by issues such as leaks, damage, a faulty well pump, or a clogged well screen. Other factors, such as the surrounding geology, regular precipitation, and proper maintenance, also affect the recovery rate.

Regular checks of pressure tanks, testing water quality, and cleaning intake screens.

The Moab, UT homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles