Top-rated well and pump technicians.

Get matched with top well and pump technicians in Blanding, UT

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Blanding, UT?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Blanding, UT

*The Angi rating for Well And Pump Service companies in Blanding, UT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Blanding, UT is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on April 12, 2021

Find Well and pump technicians in Blanding

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Blanding, UT and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

How do you set your well’s pressure tank? All you need to do is first drain the tank of water and find the pressure switch. Remove the switch cover and adjust the switch with a wrench—clockwise to increase water pressure, and counter-clockwise to reduce it. Each complete turn of the nut on the switch should equal 2.5 psi. Once this is done, replace the switch cover. All that’s left is to adjust the pressure of the tank itself using an air compressor and a tire gauge to support the new setting.

There are other ways to increase well water pressure. You can often increase the pressure by adjusting the valve on your pressure tank. The pressure issue may be the result of build-up along the pipes or a clog in the system, so descaling and unclogging your system can help improve the overall pressure.

If you notice that your well pump runs continuously, it’s important to take action quickly to avoid further damage. A few common issues may be to blame for a continuously running well pump, such as mechanical damage, a faulty pressure control switch, low water level, prime loss, and leaking pipes and fixtures.

Well pump repair might be covered by your homeowner’s insurance, but it’s typically not. If the damage results from a major storm in your area, flooding, a fire, or some other natural catastrophe, then you should consider filing a claim for the damage. However, if the issue is the result of an aging well pump, your policy will very likely not cover the repair cost. In either case, you should hire a well pump professional inspect your well pump, and then use that information to decide whether or not you should file a claim.

Here are some signs of a bad well pump that a pro should look at: 

  • If your well pump isn’t pumping water, you could have a leak or malfunctioning pump on your hands. 

  • If your water pump runs nonstop, there might be a leak or problem with the pressure tank, which can cause the pump to fail. 

  • Low water pressure can happen because of your pressure tank, low-water levels, or a wrong-sized pump. 

  • Dirt or sediment in your water can be a problem with a powerful pump, damaged pump filter, or the pump’s location.

The Blanding, UT homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles