Top-rated drywall pros.

Get matched with top drywall pros in Coram, NY

Enter your zip and get matched with up to 5 pros

Need a pro for your drywall service project in Coram, NY?

Select your specific project to find the pro for you.

TRUSTED BY CORAM, NY HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon280
    Verified drywall services reviews

Find Drywall pros in Coram

Avatar for KWD Group, Inc.
KWD Group, Inc.
4.5(
16
)
Drywall - InstallDrywall - Install - For BusinessDrywall - Repair+1 more

Serving Coram, NY and surrounding areas

Approved

In business since 2020

Free estimates

Credit card accepted

"KWD Group was prompt, punctual and transparent. The drywall repair was completed to my satisfaction and KWD cleaned up at the end of each day. Price of job was fair. Would definitely recommend to a friend."
Basement  remodel
Ready for sheetrock
Spackle
Spackle
Flooring

+6

Response time2 days
1 neighbors recently requested a quote
Recommended by100%of homeowners
Avatar for Square Construction and Design, Inc.
Square Construction and Design, Inc.
4.7(
88
)
Drywall - Repair - For Business

Serving Coram, NY and surrounding areas

Approved

In business since 2013

Free estimates

Warranties offered

"Had old grout removed from slate stoop and walkway and replaced. Work was very good , workers friendly and cleaned up after done. Protected cars and open garage with plastic covers from dust created during removal of old grout. Would recommend this compant"
Basement Before
Basement Before
Basement After
Basement After
Basement, accent Brick wall

+39

Response time7 hrs
Response rate90%
2 neighbors recently requested a quote
Avatar for BLI Painting LLC
BLI Painting LLC
4.9(
11
)
Drywall - Repair

Serving Coram, NY and surrounding areas

Approved

In business since 2023

Free estimates

Small jobs welcome

"I had a leak in my upstairs bathroom, so we had to open the bathroom wall and the ceiling to fix the leak. BLI came out and did a phenomenal job fixing the sheet rock. The job was seamless, quick and very clean. We were worried about the dust being everywhere. They made the ceiling and wall look like new with minimal dust. Then he spent a good amount of time on his hands and knees cleaning after. I would absolutely use them again and recommend them to my family and friends."
Ceiling
Ceiling
3
4
5

+37

Response time4 hrs
Response rate100%
Recommended by100%of homeowners
...
Showing 1-10 of 522
Drywall questions, answered by experts

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

Metal corners, often referred to as corner beads for square corners, are used on drywall installations to provide structural reinforcement to vulnerable outside corners. Their usage safeguards against chipping, denting, or other forms of damage, enhancing the overall durability of the wall. Metal corners also offer a precise and straight edge that facilitates sharp and clean lines, crucial for achieving a polished and professional finish.

Yes, professionals often repair minor wall openings made for insulation injection to restore the surface.

Yes, you can hammer a nail into a wall stud. But before you do, it’s important to confirm that you’re actually nailing into a stud—and not wiring, pipes, or ductwork. To check, find a few more studs in the wall, then measure to make sure they’re either 16 or 24 inches apart.

You should leave a gap between drywall sheets because they naturally expand and contract along with the building framing as temperature and humidity change. Most pro drywall installers leave a gap of about ⅛ inch between drywall sheets, allowing the sheets to expand, contract, and shift without cracking or becoming damaged. If you don’t leave enough gaps between slabs, the edges will press against each other when they expand, and the pressure can cause visible cracks.

The Coram, NY homeowners’ guide to drywall services

From average costs to expert advice, get all the answers you need to get your job done.