Top-rated concrete cutting pros.

Best concrete cutting pros near Mora, MN

Enter your zip and get matched with up to 5 pros

Need a pro for your concrete cutting project in Mora, MN?

Select your specific project to find the pro for you.

Top-Rated Concrete cutting pros in Mora - Updated Nov 2026

Avatar for American Waterworks
American Waterworks
4.5(
173
)
Concrete Flatwork - Repair & Resurface

Serving Mora, MN and surrounding areas

Approved

In business since 1989

Free estimates

Warranties offered

"They did great. The entire surface was level and free from tripping hazards. It is important to have them seal the cracks because there will be water from snow melt and the concrete will move. This will get you the 5 yr warrantee just in case."
Another Sinking Floor
Dirt Crawlspace in Elk Mound, WI
Concrete stoop had sunk over 6 inches
Foundation Failure Signs
Increased Efficiency of Crawlspace in Elk Mound

+156

Response time4 hrs
472 neighbors recently requested a quote
Recommended by91%of homeowners
Avatar for Simstone Concrete Works Inc.
Simstone Concrete Works Inc.
3.7(
19
)
Concrete Flatwork - Repair & Resurface

Serving Mora, MN and surrounding areas

In business since 1998

Credit card accepted

"Initial estimate was for the concrete tear out only. Emailed Ross for a side visit. He came the same day. Quoted $1700 ($1200 for 4 inch). After the tear out was done, I asked him to quote the class five preparation. We agreed on $1350 and the work was done the next day. Everything was done on time. He left the work side and street clean. Everything is ready for me to put the pavers down. Very nice to work with. Good job."
Additional Photos
Additional Photos
Additional Photos
Simstone Concrete Works Inc.
Simstone Concrete Works Inc.

+4

Recommended by75%of homeowners
Avatar for MINNESOTA HARDSCAPES LLC
MINNESOTA HARDSCAPES LLC
5.0(
3
)
Concrete Flatwork - Repair & Resurface

Serving Mora, MN and surrounding areas

Free estimates

Emergency services offered

Warranties offered

"We could not be happier with the outcome of this project! Keenan and his team saved us from a DIY project that we bit off more than we could chew. He came out and gave us a quote less than 24 hours after reaching out to him and was able to get started on the project the following weekend. He was willing to work with the materials we had already purchased saving us the headache of returning everything. When we ran into issues with our pavers he took it upon himself to remedy the issue with the home improvement store the materials were purchased through. Again, going above and beyond what was agreed upon. He was upfront with cost changes as the project progressed and was cognizant on where he could save us money. We would, with not doubt, hire Keenan again."
Concrete patio
Concrete patio
Paver Patio
Pavers and Hardscaping Project
Paver repair

+29

Recommended by100%of homeowners
Avatar for Edward LLC
Edward LLC
5.0(
1
)
Concrete - Sawing or RemovalConcrete - Sawing or Removal- For BusinessConcrete Flatwork - Repair & Resurface

Serving Mora, MN and surrounding areas

In business since 2018

Free estimates

"Beautiful work and attention to detail on my remodel of an early 1900’s home in Cambridge. They did a unique stomp texture on the ceiling with a knockdown that resulted in a beautiful marble design. I have had a lot of compliments on this. The driveway and sidewalks were over excavated sand replaced and compacted. It has been a year now with no frost heave. Very happy with the results."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+6

Recommended by100%of homeowners
Showing 1-10 of 15
Concrete Cutting FAQs, answered by experts

Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Yes, you can cut up a box spring., but you’ll need to do so in layers. You can clear the fabric and fluff away to reveal the springs before removing them as well.

This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes. 

The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use. 

You should not do your own welding unless you have the proper training and experience. Most home electrical systems can only handle MIG welding, which creates weaker bonds than TIG welding and won’t work on certain metals or metal thicknesses. Both welding forms usually require the use of shielding gas, which can be dangerous to store at home. Additionally, welding machines create temperatures of over 3,000 degrees, and the sparks can blind you if you don’t have the proper equipment. As such, it’s usually better to hire a professional welder for your welding projects.

The Mora, MN homeowners’ guide to concrete cutting services

From average costs to expert advice, get all the answers you need to get your job done.