Top-rated drywall insulation pros.

Best drywall insulation pros near Benton Harbor, MI

Enter your zip and get matched with up to 5 pros

Need a pro for your drywall insulation project in Benton Harbor, MI?

Select your specific project to find the pro for you.

TRUSTED BY BENTON HARBOR, MI HOMEOWNERS

  • Average homeowner rating star icon4
    Average homeowner rating
  • Verified reviews icon44
    Verified drywall insulation services reviews

Top-Rated Drywall insulation pros in Benton Harbor - Updated Nov 2026

Avatar for Spray Foam Genie of South Bend
Spray Foam Genie of South Bend
4.9(
14
)
Blown-In Insulation - Install or UpgradeInjection Insulation - Install

Serving Benton Harbor, MI and surrounding areas

Approved

Super Service Award Winner

In business since 2024

Free estimates

Emergency services offered

"Highly recommended they worked on my Storage barn Friday ,Saturday and finished on Sunday to do clean up which Iâ m so thankful with because they work 7days out of the week . Easy to work with and flexible with scheduling .Thank you Spray Foam Genie keep up the good work ."
Barn (1)
Barn (1)
Barn (1)
Workshop
Walls

+6

Response time2 days
Response rate97%
44 neighbors recently requested a quote
Avatar for USA Insulation of Kalamazoo
USA Insulation of Kalamazoo
4.3(
17
)
Blown-In Insulation - Install or UpgradeInjection Insulation - Install

Serving Benton Harbor, MI and surrounding areas

Approved

In business since 2021

Free estimates

Credit card accepted

"Great work, very personable, professional, courteous, and reasonably priced. Received blow in insulation for garage and entire attic in house… they hammered it out, did a quality job, and work very hard."
Finished House 1
Finished House 2
Our Work
Our Work
Our Work

+6

Response time2 days
13 neighbors recently requested a quote
Recommended by92%of homeowners
Avatar for USA Insulation North Central Indiana
USA Insulation North Central Indiana
5.0(
4
)
Blown-In Insulation - Install or UpgradeInjection Insulation - InstallInsulation - Install or Upgrade

Serving Benton Harbor, MI and surrounding areas

In business since 2019

Free estimates

Credit card accepted

"The owner of USA Insulation, Mark Owens, and his associate spent over an hour inspecting every nook and cranny of my 2800 Sq. Ft. two story home. After which, Mark spent a lot more time reviewing the current situation regarding my home's insulation. Then he thoroughly explained what needed to be done to correct the situation I was so impressed with his knowledge and professionalism and explanation of options. In the end, I decided that the one or two more years I intended to be in this home was not worth the investment. I suggested a partial and less expensive fix that would have resulted in a contract for him. Instead of taking my money, he explained why this would not fix the issue in the coldest room in the house and why it would not be a wise investment for me. I have great respect for his integrity and would recommend him as a professional of the highest caliber. If I should decide not to move in a few years, I will be calling USA Insulation, Mark Owens."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+1

Recommended by100%of homeowners
Avatar for American Basement Solutions
American Basement Solutions
4.3(
46
)
Blown-In Insulation - Install or UpgradeInjection Insulation - InstallInsulation - Install or Upgrade

Serving Benton Harbor, MI and surrounding areas

In business since 1992

Credit card accepted

"It was a small job. They sealed the vents to the crawlspace, then, since there was already solid insulation panels on the walls, put a vapor/moisture barrier, in the form of a tarp, 4 feet wide and as long needed, completely around the crawlspace. It was then sealed to the walls with "nails" and adhesive. This seals the wood frame of the house from the 'Outside", the ground, which is the floor of the crawlspace. A 20 mil thick, quite heavy, "floor" was installed, also in the form of a tarp, It went up the walls about 3 feet and was taped to the 'tarp" on the walls, using a tape made for this application. The piers were wrapped with the same stuff and taped to seal the inside from the outside. the "floor" is also a vapor/moisture barrier, but, heavy enough to walk on if needed. This basically makes the crawlspace another room, rather than the outside. Our house is one year old and was already getting mold on the floor joists. Since the air in the crawlspace will now be heated in the winter and cooled in the summer, just like the rest of the house, the mold and cold (52 degrees) floors we experienced last winter will hopefully be eliminated. We shall see when dumb winter gets here."
Additional Photos
Additional Photos
Additional Photos
Recommended by85%of homeowners
Showing 1-10 of 18
Drywall Insulation FAQs, answered by experts

The easiest way to tell if a wall is load bearing is to check if it’s an exterior wall or if it runs perpendicular to the joists above and below it (or parallel to beams). Exterior walls are almost always load-bearing, and walls that run under beams or parallel to them are also usually load-bearing. There are exceptions to these rules, and walls that don’t fit into these categories can still be load-bearing. If you’re unsure, hire a structural engineer to look at your home to assess whether or not the wall is structural.

The best tool for cutting a hole in drywall is a drywall saw. Its serrated blade and ergonomic design make it efficient for both straight cuts and more intricate shapes, ensuring clean and precise results in various drywall cutting applications.

While not always necessary, you can glue a drywall ceiling in addition to using screws or nails. Drywall is typically secured to ceiling joists with fasteners, which is often sufficient. However, adding construction adhesive can offer benefits like preventing sagging, bridging gaps, and reducing air leaks for better energy efficiency. It may also be used for specific acoustic or insulation needs. On the other hand, many professionals advise against it because properly placed screws make the drywall structural, glue doesn't add strength, and it makes future repairs or replacements significantly more difficult. Ultimately, it's best to follow local building codes and project-specific requirements to decide if adhesive is right for your ceiling.

If you only have tiny holes in your drywall (for example, dents or nail marks), you probably won’t need a patch kit. Instead, you can plug the hole with a small amount of spackle. Once the spackle dries, you can sand the area and paint over it—just like you would in the steps outlined above.

Choose a drill bit that is the size of the screws of the anchors you will use. You aren’t drilling through metal or concrete—hopefully—so any standard twist, wooden or all-purpose drill bit will work fine. It’s also important to have a screwdriver capable of drilling through the drywall and into the stud. The good news is most available drills, even the older ones, can do this with no issue.

The Benton Harbor, MI homeowners’ guide to drywall insulation services

From average costs to expert advice, get all the answers you need to get your job done.