Top-rated electricians.

Get matched with top electricians in Harold, KY

Enter your zip and get matched with up to 5 pros

Need a pro for your electrical service project in Harold, KY?

Select your specific project to find the pro for you.

Find Electricians in Harold

Avatar for RS Lightning Protection
RS Lightning Protection
4.9(
81
)

Serving Harold, KY and surrounding areas

Approved

In business since 1999

Free estimates

Emergency services offered

"I estimate I have just under $100k in electronics and appliances in my house. We have significant lightning storms in my location. To NOT have lightning suppression installed is significant risk in my mind based on my location in New Jersey. RS LIGHTNING PROTECTION was responsive with a quick cost estimate and a reasonable price based on my research for installation. By the way...installation is part art, such as bends in cable are not more than 90 degrees. It's not just about running grounded cables. This installation in conjunction with surge protection on my electrical panel performed by my electrician and cable protection gives me significant piece of mind that all my appliances and electronics are protected from lightning and any potential surge generated by a near strike. Mr Richard Sherlock knows his subject. Highly recommended. Five stars."
Carriage house concealed
New home
Storage building
Beau
Grain lake system

+12

Response time3 days
11 neighbors recently requested a quote
Recommended by95%of homeowners
Avatar for W B Lightning Rods
W B Lightning Rods
4.6(
367
)

Serving Harold, KY and surrounding areas

Approved

In business since 2001

Free estimates

Warranties offered

"WB Lightning is focused on customer service. The company provided good communication and responded very quickly to my inquiry for a quote. WB Lightning is a respected company, I had another electrical service provider tell me I made a good choice when I hired WB Lightning Rods."
lightning protection
 Residential LPS
lightning protection
 Residential LPS
lightning protection

+79

Response time1 day
63 neighbors recently requested a quote
Recommended by98%of homeowners
Avatar for Renewable Engineered Systems
Renewable Engineered Systems
4.7(
12
)

Serving Harold, KY and surrounding areas

In business since 1998

Free estimates

Emergency services offered

"Well we were going to do a ground mount using re-purposed
metal, but there was not enough of it. So Renewable Engineered Systems designed
a system for the roof of the house. We Worked with Brian Brown who helped us
decide what to use.   The solar panel
system is very neat. Get to watch my power everyday.

"
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+14

Recommended by100%of homeowners
Showing 1-10 of 32
Electrical questions, answered by experts

There are several indicators that a single-pole switch is bad: the switch is warm or hot to the touch, sparks are sometimes present when turning the switch on or off, you hear a buzzing sound or other weird noise coming from the switch, the connected light flickers when you turn on the switch, and the light doesn't turn on at all with the switch. If you notice any of these, replace the switch or call a pro straight away.

In most cases, line wires are located at the bottom of a panel or device, while load wires are located at the top. Line wires are generally black, while load wires are typically red or black. To tell for sure, you can use a multimeter or volt pen to test the wire. A live or line wire will always carry a charge, while a load wire will only carry a charge when it’s in use.

Typically, when a 3-way switch only works when one switch is on, this is one of the most telltale indicators that the switch has gone bad (although this could also be the result of faulty or loose wiring). To diagnose the issue, toggle each switch until the light comes on. Once it’s on, toggle each switch separately again; the switch that doesn’t turn the light off is the bad switch. 

Wire color codes vary depending on the region. For instance, the United Kingdom has updated its wiring codes to match Europe's color system. The United States wiring color code is different, as is Australia's. Because the color code system isn’t universal, it’s essential to hire an experienced electrician to perform any electrical work to ensure it is done correctly.

That depends on your setup. If a circuit breaker already has GFCI protection, then everything connected to that specific circuit is being monitored. You don’t need additional GFCI outlets on that breaker.

However, if the breaker is not GFCI, then you should have GFCI receptacles for at-risk outlets nearby water sources, because they are not receiving protection. Breakers in a breaker box can vary between GFCI and non-GFCI. Look for GFCI labels on the breaker or try to find the breaker model number to look it up if you aren’t sure.

The Harold, KY homeowners’ guide to electrical services

From average costs to expert advice, get all the answers you need to get your job done.

What do you need done? We’ll find top pros.
  • 🌱 "Mow a small front yard"
  • 🛠 "Fix a leaking pipe under the sink"
  • 🏠 "Repair shingles on an asphalt roof"