"Ed Riley is extremely knowledgeable about what causes lighting and how to protect from it. He explained to me which and how structures develop static electricity that lead to lighting discharges in a way that the physics made sense to me. They were also reasonably priced and kept their word. Definitely recommend them."
"John Corrigan and his sons are outstanding! They did outstanding work installing our lighting rods at a reasonable price. They were prompt, very professional and honest. I would call them again and recommend them to anyone."
"We were contacted immediately regarding adding a lightning protection system on our home. Seamus was very thorough and knowledgeable regarding our concerns. He and his crew showed up and were very professional and efficient. We are very pleased with the installation and highly recommend Donahue’s."
"The problem turned out to be a burned out small electric door switch. I believe the price was way too expensive for the service performed and the price of the door switch. What more can I say? It got done."
"Jim Benton of Country Boys Electric came out the day after my call for a bid. He walked through our shell of a log cabin in the woods, was very thoughtful, made many great suggestions about where to put lights and plugs, described the work they would do and within a few days we has his written bid. We liked and trusted Jim immediately and they started to work in a few days. His workers were very professional, arrived on time, worked well with us. They did all the wiring and then had to wait about a month for the sheetrock and painters to do their work. We called them back and they were ready to install lights and fans and finish the job. We were so please with their work. They were very reliable and on time, even though they had to drive 40 miles from their shop to our place each day.We would highly recommend them to others. "
"My house was under construction. and had already gotten struck by lightning so time was critical as I knew it could happen again. I have a home with tall roof peaks and built on a hill. They came out quickly and started right away and their prices were way less than the other company s. I will use them again when my barn is constructed."
"I have had my Aztec Renewable Energy solar panels for over two years, and I am very pleased with the performance of the equipment as well as the whole process. Upon activation of my system, my average monthly electric bill went from over $150 to under $15. Additionally, it has required no service or maintenance. The initial sales call was low pressure, and Charles took the time to educate us regarding the use of solar energy. The cost of the installation was exactly what was quoted; and the installers were professional, experienced, and very proficient. The system is functioning just as efficient as it did on day one. I would recommend solar panels to save money and do good for the environment. I recommend Aztec because of their expertise and courtesy."
If you’re moving wires, installing new wires, or installing new fixtures in the space you’re insulating, then you will need to hire a licensed electrician to do that portion of the job for you. However, if you just intend on replacing old insulation or adding new insulation over existing insulation, then you don’t need to hire one. Your insulation installer will work around wiring, fixtures, outlets, and switches, even if they’re installing fiberglass batts in the voids where wires run. However, you will need an electrician if you suspect a problem with your wiring during the insulation work.
No, not all thermostats require a C-wire. Older manual and programmable thermostats typically do not need one. While many smart thermostats do require a C-wire to function correctly, some models can operate without one, often at the expense of certain features. A C-wire provides a constant source of power, which enables the thermostat to stay connected to Wi-Fi and keep its display screen lit on-demand. If you are upgrading from an older thermostat to a smart model that requires a C-wire, you may need to install one first for it to work as intended.
In most cases, line wires are located at the bottom of a panel or device, while load wires are located at the top. Line wires are generally black, while load wires are typically red or black. To tell for sure, you can use a multimeter or volt pen to test the wire. A live or line wire will always carry a charge, while a load wire will only carry a charge when it’s in use.
Incorrectly wiring a single-pole switch results in the connected light or device not turning on or tripping the circuit breaker. Although it doesn't matter which terminal the hot wire and the load wire connect to, mixing up a circuit wire with a ground or having loose connections can prevent the switch from working.
Yes, in some locations, it is required by the National Electric Code (NEC) to have a transfer switch installed for electrical emergencies. In addition to following electrical code, generator transfer switches ensure your home is fully protected during a power outage. By switching the power from the main breaker to the generator breaker, you can seamlessly operate your HVAC, lights, appliances, devices, and more during an emergency.
The Stratford, TX homeowners’ guide to electrical services
From average costs to expert advice, get all the answers you need to get your job done.
Before you hire a licensed electrical contractor, you should learn the cost to run electric from the road to your house so you can budget for the project.
Is it time to upgrade your electrical panel? For the sake of safety, find out sooner than later by exploring our top signs that it’s time for an upgrade.
