Top-rated woodworkers.

Get matched with top woodworkers in Lott, TX

Enter your zip and get matched with up to 5 pros

Find Woodworkers in Lott

Avatar for Aqua Werx, LLC
Aqua Werx, LLC
4.8(
83
)

Serving Lott, TX and surrounding areas

Approved

In business since 2014

Free estimates

Credit card accepted

"He was great and made sure he was hanging the lights as we wanted. Did not leave until he was sure we were pleased with the installation."
Ridgewood Country Club
Ridgewood Country Club
Ridgewood Country Club
Ridgewood Country Club
Ridgewood Country Club

+7

Response time2 days
6 neighbors recently requested a quote
Recommended by100%of homeowners
Wieland Construction
3.9(
10
)

Serving Lott, TX and surrounding areas

Approved

In business since 1991

Free estimates

Credit card accepted

"Robert and his crew were fabulous. They operated professionally and with integrity. They started work each morning around 8:00 am sharp. My husband and I are very please with our Bathroom Remodel. I also had other small jobs done while they were there. They did not complain but were willing to accommodate me and my ideas. I will be hiring them again for our future Home Renovation Projects."
Recommended by100%of homeowners
Avatar for Moorish Weld co.
Moorish Weld co.
New to Angi

Serving Lott, TX and surrounding areas

Approved

Free estimates

Emergency services offered

Small jobs welcome

With a combined 14 years of experience in metal and wood work. We are able to offer services from welding to cabinet/trim work. \n\nWe service the surrounding areas of Austin, Houston & College Station.\n\nWe specialize and welding repair/metal fabrication and wood repair/installation and fabrication and finish. \n\nOur Motto is Precision. Strength. Legacy. And we strive to meet and keep that reputation.

Heavy tanker repair.
Service/Repairs kitchen
8 neighbors recently requested a quote
Avatar for Full Scale LLC
Full Scale LLC
5.0(
1
)

Serving Lott, TX and surrounding areas

Approved

Free estimates

Warranties offered

Credit card accepted

"Nate Davis came out on time me repaired the doors in less time than his estimate,He gave me an estimate on repairing damaged siding and repairing and painting a room the work was finished under his estimate I highly recommend him for any remodeling and repairs"
Sky Shower
Sky Shower
2 neighbors recently requested a quote
...
Showing 1-10 of 135
Woodworking questions, answered by experts

No, beams are the primary load-bearers for flooring or roofing systems, and they distribute the weight of the structure to your foundational supports, while joists bear far less weight and distribute their loads to the beams. Beams are usually thicker and longer, and they have support posts or foundation walls beneath them for support.

If you don’t have a power saw with a blade where you can adjust the angle, you could use a miter box and hand saw to make the cuts. The miter box contains wide slots to support the piece of baseboard and other narrow slots to accommodate the blade of the hand saw. However, it’s tough to make non-standard cuts beyond 30 or 45 degrees when using a miter box.

Before hiring a carpenter, the most important thing is to make sure they are properly qualified and insured for the job. It’s more than reasonable to ask your prospective carpenter for customer references, as well as about their licensing and insurance. You should also consider choosing a carpenter that specializes in your specific project area to ensure high-quality results. 

Joists do distribute their load to beams, but they don’t sit on top of the beams. Instead, home builders nail or screw the joists directly to the beams such that the end of the joist butts up against the edge of the beam. Beams can sit on other beams for support, but you’ll never see a joist sitting on top of a beam or another joist.

There are two ways you can cut trim for doorways: with a miter saw or a table saw. Mitered joints need a 45-degree angle. If you’re unfamiliar with a miter saw, you might want to consider buying extra trim pieces or choosing butted joints instead. One wrong cut, and you’ll need to power up the saw again with a new piece. 

Butted joints—also called shaker style—don’t need a 45-degree angle. Instead, your side pieces attach perpendicularly to the header trim and only require a straight cut.

The Lott, TX homeowners’ guide to woodworking services

From average costs to expert advice, get all the answers you need to get your job done.