Top-rated welders.

Get matched with top welders in Kenhorst, PA

Enter your zip and get matched with up to 5 pros

Need a pro for your welding project in Kenhorst, PA?

Select your specific project to find the pro for you.

Find Welders in Kenhorst

Avatar for Schultz Design & Fabrication
Schultz Design & Fabrication
5.0(
5
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomSheet Metal and Ornamental Metal - Fabricate

Serving Kenhorst, PA and surrounding areas

Approved

In business since 2020

Free estimates

Credit card accepted

"I cannot be happier with this pro. I highly recommend him. He underpromised and overdelivered. He installed a metal spiral staircase by Paragon stairs: They did an exceptional job. Flawless. They took the time to measure and level every step. Drove from an hour away.outstanding quality and customer service: I have done a lot of remodeling over time and I would give them a 10 star if I could!"
Response time5 hrs
Recommended by100%of homeowners
William Staniscia
4.2(
15
)
Steel Beams (Structural) - Install

Serving Kenhorst, PA and surrounding areas

Approved

In business since 1990

Free estimates

Offers commercial services

"We hired Bill to finish our basement. Bill and his son did an excellent job. They pay attention to all details, really care about the job at hand, and make sure to exceed all expectations. Not only did they complete all quoted work, but troubleshot other issues in the basement and made recommendations to fix other issues. They are extremely professional and considerate. We have young children at home and they would always give a heads up if they'd be making loud noises, etc. I would highly recommend this company and will be hiring them again in the near future!"
Response time2 days
Response rate100%
4 neighbors recently requested a quote
Grady's Painting Plastering/Construction
2.0(
174
)
Wrought Iron Fence - Repair or Weld

Serving Kenhorst, PA and surrounding areas

Approved

In business since 1969

Free estimates

Emergency services offered

"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
Response time11 hrs
Response rate100%
Recommended by57%of homeowners
Avatar for Fegely Fabrication and Repair
Fegely Fabrication and Repair
1.0(
1
)
Metal Stairs and Railings - RepairMetal Structure or Object - Create CustomSheet Metal and Ornamental Metal - Fabricate

Serving Kenhorst, PA and surrounding areas

Approved

In business since 2021

Free estimates

Emergency services offered

We have the experience and we are committed to providing quality workmanship and superior customer service on all our applications. We at Fegely Fabrication and Repair\n strive to maintain our reputation as a high quality, very service oriented company with our main focus being customer satisfaction.\n

Response time40 mins
...
Showing 1-10 of 104
Welding questions, answered by experts

Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective. 

Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation. 

It will likely take an experienced pro less than an hour to install a ground rod, which is another reason why letting them handle the job is such a good idea. Safety concerns aside, it would likely take you much longer to install a ground rod if you decided to take this one as a DIY job.

Professional metal fabricators typically charge around $70 per hour, but the total cost of your project will depend on several factors. The largest cost drivers are the size, complexity, and design of the project, as well as the price and type of metal used. A good way to estimate the total cost is to multiply the cost of raw materials by four; typically, one-quarter of the total goes toward materials and three-quarters toward labor. Your geographic location can also influence costs, as labor and material prices vary by region.

Costs depend on unit complexity, labor, wall mounting needs, and additional accessories like floating shelves.

Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).

The Kenhorst, PA homeowners’ guide to welding services

From average costs to expert advice, get all the answers you need to get your job done.