Top-rated well and pump technicians.

Get matched with top well and pump technicians in Raton, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Raton, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Raton, NM

*The Angi rating for Well And Pump Service companies in Raton, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Raton, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on July 01, 2024

Find Well and pump technicians in Raton

Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,688
)

Serving Raton, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Wells and Pumps questions, answered by experts

A submersible pump should be at least 10 feet from the bottom of the well to minimize the risk of the pump drawing debris into the well water. Submersible pumps work best for wells that are 25 feet deep or less. If you have a deeper well, choose a jet pump instead of a submersible model.

Schedule annual inspections, test water pressure, and protect the pump from freezing temperatures.

The cost to fix low water pressure heavily depends on the cause of the problem. In some cases, all you need to do is open a valve, which won't cost you anything. However, plumbing repairs cost an average of $325, so if you have a broken pipe or other plumbing problems, you might pay something close to that figure, or more, depending on the issue.

If you notice any changes to the water coming from your well, consider that a sign to get a well inspection. For example, if the water is foul-smelling, bad-tasting, cloudy, or discolored, you should call a pro. It’s also a good idea to schedule an inspection if you observe a loss of water pressure, broken equipment, loss of well capacity, or other unusual signs.

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

The Raton, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles