Top-rated well and pump technicians.

Best well and pump technicians near Cleveland, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Cleveland, NM?

Select your specific project to find the pro for you.

Top-Rated Well and pump technicians in Cleveland - Updated Nov 2026

Avatar for Art's Plumbing and Heating, Santa Fe, NM
Art's Plumbing and Heating, Santa Fe, NM
4.0(
4
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Cleveland, NM and surrounding areas

In business since 2000

Free estimates

Emergency services offered

Hello, and welcome to Art's Plumbing and Heating & Cooling! We are a family-owned and operated air conditioning, furnace, plumbing and drain repair and installation company, and I would love for our team to have the opportunity to serve you! We take pride in offering the best customer service, the most technically trained service professionals and the friendliest team. EMERGENCY SERVICE AVAILABLE..

Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+12

Recommended by100%of homeowners
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Cleveland, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Wells and Pumps FAQs, answered by experts

A shallow-well pump can pull water up to 25 feet deep. A deep-well pump can pull water up to 90 feet deep. A deep-well submersible pump can pull water up to 300 feet deep. Make sure to consult a pro to find out how deep your well is and get the right pump for your needs.

Here are some signs of a bad well pump that a pro should look at: 

  • If your well pump isn’t pumping water, you could have a leak or malfunctioning pump on your hands. 

  • If your water pump runs nonstop, there might be a leak or problem with the pressure tank, which can cause the pump to fail. 

  • Low water pressure can happen because of your pressure tank, low-water levels, or a wrong-sized pump. 

  • Dirt or sediment in your water can be a problem with a powerful pump, damaged pump filter, or the pump’s location.

If you notice any changes to the water coming from your well, consider that a sign to get a well inspection. For example, if the water is foul-smelling, bad-tasting, cloudy, or discolored, you should call a pro. It’s also a good idea to schedule an inspection if you observe a loss of water pressure, broken equipment, loss of well capacity, or other unusual signs.

The cost to replace a well-pump motor will depend on the size, but this repair is often as costly as installing a new pump. Generally, a well-pump replacement will cost between $950 and $2,650, with an average of $1,800. Other factors like pump type and pipework will impact your final cost.

The average three to four-bedroom home typically uses a well pump rated for 8 to 12 gallons per minute (GPM). To find the most accurate size for your specific needs, a common rule of thumb is to count the number of water fixtures and appliances in your home and aim for that number in GPM. This calculation allows for about one gallon of water per minute per fixture. Because estimating the correct size can be challenging, it's best to have a professional technician make the final determination. A professional can ensure your pump provides sufficient water for your home, especially during peak usage hours.

The Cleveland, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.