Top-rated well and pump technicians.

Best well and pump technicians near Eunice, NM

Enter your zip and get matched with up to 5 pros

Need a pro for your well and pump service project in Eunice, NM?

Select your specific project to find the pro for you.

Verified Reviews for Well And Pump Service pros in Eunice, NM

*The Angi rating for Well And Pump Service companies in Eunice, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

*The HomeAdvisor rating for Well And Pump Service companies in Eunice, NM is a rating based on verified reviews from our community of homeowners who have used these pros to meet their Well And Pump Service needs.

Last update on March 04, 2025

Top-Rated Well and pump technicians in Eunice - Updated Nov 2026

Permian H2O Solutions, LLC
5.0(
2
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Eunice, NM and surrounding areas

In business since 2015

Free estimates

Emergency services offered

Permian H2O Solutions, LLC is a licensed and insured water well drilling and service company. We pride ourselves on great service and pricing. Most service call are taken care of the same day. Permian H2O Solutions has been in business for 5 years serving the Permian Basin. We service a 150 mile around Midland/Odessa.

Recommended by100%of homeowners
Request Quote
Avatar for American Home Shield – Home Warranty
American Home Shield – Home Warranty
3.5(
5,689
)
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Eunice, NM and surrounding areas

In business since 1971

Credit card accepted

"Well, the first time the replacement was ordered it was the wrong one, which of course, delayed the installation a week. When it was finally installed I had to pay an additional $850 for code upgrades. This I was not informed of by Home Shield. Then we noticed that there was water on the garage floor and found that the pipe coming in from the wall was leaking at the wall so had to call the plumbing company back out to fix it. They first tried to say it was not their fault but since there wasn't a leak before they installed they did fix it. I have used Home Shield a few times before and never had a problem. Some of the companies they use are not the best so you have to research them before you commit. I have found HS service to be good if you do your homework. At the end of the day I was without hot water for almost 3 weeks but it was do to the plumbing company they sent out."
Additional Photos
Additional Photos
Additional Photos
Additional Photos
Additional Photos

+2

Recommended by65%of homeowners
Request Quote
Avatar for LoneStar Developers
LoneStar Developers
New to Angi
Well Pump - Install or ReplaceWell Pump - Repair or Service

Serving Eunice, NM and surrounding areas

Free estimates

Small jobs welcome

Credit card accepted

Need a reliable commercial or Residential construction crew? \n\nLonestar Developers has you covered. \n\nWe specialize in: \n• Framing \n• Plumbing \n• Electrical \n• Drywall \n• Acoustical Ceilings \n• Mud & Tape \n\nQuality work. Honest service. Built the Texas way. 🤘 \n\n📩 Message us today for quotes or project inquiries.

Request Quote
Wells and Pumps FAQs, answered by experts

The pressure in a well pressure tank should be set 2 to 3 PSI below the pump's cut-on pressure. The cut-on pressure is the lower number in the pressure setting (e.g., the '30' in 30/50 PSI) and is the point at which the pump starts. The cut-out pressure is the higher number, where the pump stops.

For example:

  • If your pressure switch is set to 30/50 PSI, the tank pressure should be 27-28 PSI.

  • If your pressure switch is set to 40/60 PSI, the tank pressure should be 38 PSI.

Common pressure settings for household applications include 20/40, 30/50, and 40/60 PSI. The difference between the cut-on and cut-out pressure is typically 20 PSI.

Here are some signs of a bad well pump that a pro should look at: 

  • If your well pump isn’t pumping water, you could have a leak or malfunctioning pump on your hands. 

  • If your water pump runs nonstop, there might be a leak or problem with the pressure tank, which can cause the pump to fail. 

  • Low water pressure can happen because of your pressure tank, low-water levels, or a wrong-sized pump. 

  • Dirt or sediment in your water can be a problem with a powerful pump, damaged pump filter, or the pump’s location.

A professional well inspection takes between one and three hours. This includes the time it takes for the inspector to visually check the condition of your well, test its equipment, and collect water for testing. After the pro sends the water samples to the lab, you can expect to receive the results in three to 10 days.

Yes, you can shock a well yourself, but it can be dangerous if you don’t know what you’re doing. We recommend calling a pro, but if you decide to do it yourself, make sure to follow proper safety precautions. This means wearing the correct safety gear, such as rubber gloves, goggles, and boots. You should also mix the chlorine solution in an open area with plenty of ventilation. Also, make sure not to drink or use the water for a few days afterward, until you’ve flushed the system and retested the water.

A submersible pump should be at least 10 feet from the bottom of the well to minimize the risk of the pump drawing debris into the well water. Submersible pumps work best for wells that are 25 feet deep or less. If you have a deeper well, choose a jet pump instead of a submersible model.

The Eunice, NM homeowners’ guide to well and pump services

From average costs to expert advice, get all the answers you need to get your job done.

See all articles