At PureLife Welding, we take great pride in our experience, expertise, quality and customer service that we provide to meet the consumer's needs. It is our mission to provide excellent workmanship and complete customer satisfaction from start to completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety and quality, regardless of how large or small the job.
"David the welder very respectful communicated well answered all my questions scheduling timing very accommodating, very satisfied with the work done and clean up. I will recommend Fusion King Welding LLC to family and friends."
"Very well. Gary was very good to deal with. His quote for the job came in over 30% lower than another Angi-recommended contractor. The laborers worked very hard over two days, especially digging out and putting in posts. We didn't deal with them too much but they did a great job and the fencing looks good."
"I needed stucco repair work on an old chimney (and other spots). Grady was meticulous and thoughtful on what approaches and materials would work. Throughout the project they allocated sufficient time for each treatment to cure and inspected the work before proceeding to the next step. Grady started the project with no money down and only required ongoing payments for materials until the project was well underway. The final payment was due only after they did a final inspection. Total project cost was also below other bids."
We take great pride in our experience, expertise, quality, and customer service that we provide to meet the consumer's needs. It is our mission to provide excellent workmanship and complete customer satisfaction from start to completion of a project. In order to understand the needs and expectations of our customers, we take great care to work and communicate with every customer in a professional manner. Our reputation is based on service, safety, and quality, regardless of how large or small the job. Stick, MIG, and TIG welding done here!
"These guys are great. Hire them hands down. Great price, great follow up, great job. They are on top of everything and are in constant contact, no need to keep after them because they keep after you. They do almost everything-Welding, woodwork, roof work, concrete and foundation work, everything but HVAC. I had them to a welding job, then hired them for a roof job, and will give them much work as a real estate developer and commercial property owner, these are some of the best contractors I have found."
"I somehow managed to bend and crack the tongue on my trailer. MCT welding and fabrication provided a great service and fixed it in no time for a reasonable price."
"Very good professional workers, very helpful, courteous, attached to my budget, they really did an excellent work, they came back and checked for the project, I would recommend them to anybody."
To maintain custom or fabricated metal structures and extend their lifespan and appearance, perform regular cleaning, apply rust prevention treatments, and use protective coatings.
This all depends on the tools you have on hand and whether you’re trying to cut a straight line or shapes.
The best tool to use for straight lines is either a circular saw or table saw. When cutting shapes, a jigsaw will be the easiest and most precise tool to use.
Yes, you can use a saw to cut metal pipes. The best saw to use is a reciprocating saw, but even a fine-tooth hacksaw can get the job done. No matter which saw you use to cut metal pipes, wear protective gear, like work gloves, safety goggles, and ear plugs. Apply a firm, steady pressure to the tool, and always ensure the pipes are secured so they don't move while you make the cuts.
Cutting rectangular ductwork requires careful measurements and the right technique. Use a measuring tape and pencil to mark the cutting lines accurately. Tin snips are excellent for straight cuts on smaller ducts. For more extensive or thicker rectangular ducts, a reciprocating saw with a metal-cutting blade is effective.
Ensure the duct is well-supported and secure while cutting to prevent wobbling and maintain precision. After cutting, use a metal file to smooth any sharp edges, ensuring safety during installation.
Yes, you can cut plexiglass by hand using a sharp knife or blade (utility knife, box cutter, glass cutter, etc.).
The Yardville, NJ homeowners’ guide to welding services
From average costs to expert advice, get all the answers you need to get your job done.
When you need help with a metal project and don’t have the expertise or the time, call an expert welder for your project. Here’s how to vet and hire a welder.
