Top-rated contractors.

Get matched with top contractors in Steele, ND

Enter your zip and get matched with up to 5 pros

Need a pro for your contractor service project in Steele, ND?

Select your specific project to find the pro for you.

Find Contractors in Steele

Avatar for Kamrose Construction Inc
Kamrose Construction Inc
4.6(
12
)
Major Home Repairs (General Contractor)

Serving Steele, ND and surrounding areas

Approved

In business since 2001

Free estimates

Emergency services offered

"Wonderful to work with. The finished project was above and beyond my expectations. I highly recommend them, and will continue to hire them for future projects."
Thompson Bath/Laundry Renovation
Omaha Exterior
Fireplace Surround
Thompson Bath/Laundry Renovation
Omaha Exterior

+102

Response time3 days
13 neighbors recently requested a quote
Recommended by100%of homeowners
Avatar for Homemade Design
Homemade Design
3.7(
322
)
Major Home Repairs (General Contractor)

Serving Steele, ND and surrounding areas

In business since 2006

Credit card accepted

"I never contacted the provider or used this service in anyway. I have to
write this review so that the request to write this review stops
popping up.
The rating is bogus as it is required to be able to submit.
"
Pennsylvania Master Bathroom
Boston Small Condo Kitchen
California Client Saves with HMD Designer Discounts
Recommended by54%of homeowners
Avatar for Jill Seidner Interior Design
Jill Seidner Interior Design
3.5(
89
)
Major Home Repairs (General Contractor)

Serving Steele, ND and surrounding areas

In business since 2006

Credit card accepted

"They did a good job. She had to submit like a photo but my daughter had them work on the central are of the loft. The deal was for one room. She got a lot of good ideal from her and it was worth it for her. They were professional and I did not hear anything negative."
Recommended by55%of homeowners
Seamless Drywall and Remodeling, LLC
5.0(
1
)
Major Home Repairs (General Contractor)

Serving Steele, ND and surrounding areas

In business since 2020

Free estimates

"Brandon was hired to remove a load-bearing wall in our kitchen to open up the area between the kitchen and living room. This involved building a temporary "false wall," removing the existing wall then, and laminating two 2 x 12's set on end as a header - secured above supports at each gap-end. When that was finished he very professionally did the required drywall work including mudding, sanding, texturing, etc. From start to finish. He even went under the house and installed a "twist jack" under each gap support end to make certain the floor would not be depressed in any way. Very complete, competent, and professional!! Definitely recommend!"
Response time2 days
Showing 1-10 of 14
Unfinished Carpentry questions, answered by experts

Yes, you will need a jack for a rim joist replacement. To prevent sagging and facilitate the removal of load-bearing wood, you’ll need to relieve the pressure from this joint before beginning work. 

Due to hydraulics and other specialized equipment, a sill plate and rim joist replacement are not typically a DIY project. Hiring a professional structural engineer and experienced contractors is the best approach to replacing rotted sill plates and rim joists.

Removing a load-bearing wall affects the structural integrity of your home, so you’ll need a permit before starting the work. Building codes vary by municipality, and obtaining a permit and having the work inspected after completion will ensure you’re in compliance with all applicable regulations.

Yes, you can find ceiling joists using simple tools if a stud finder isn't available.

Using a hammer requires patience and a keen ear. Gently tap the ceiling in a grid pattern, listening for sound changes. A hollow sound indicates space between joists, while a solid, dull thud suggests a joist. Mark the location with a pencil and confirm by tapping from different angles.

Alternatively, you can use a nail, but this method will leave small holes. You'll feel increased resistance when the nail hits a joist. Mark the spot and repeat the process every 16 or 24 inches to map the joist locations. This method is considered less reliable than using a stud finder.

Yes, most services include necessary frame modifications for proper door fitting. Confirm with your provider.

An A-frame home can be cheaper to build than a traditional house, but that is not always a given. Prices can be fairly similar in some cases, depending on the location, design, and necessary site preparation. Costs for an A-frame typically run between $100 to $200 per square foot, which is comparable to the cost of a traditional home. The cost of an A-frame can come in under those numbers if you opt for a prefabricated kit.

The Steele, ND homeowners’ guide to contractor services

From average costs to expert advice, get all the answers you need to get your job done.