Top-rated toilet pros.

Get matched with top toilet pros in Selma, NC

Enter your zip and get matched with up to 5 pros

Need a pro for your toilet service project in Selma, NC?

Select your specific project to find the pro for you.

TRUSTED BY SELMA, NC HOMEOWNERS

  • Average homeowner rating star icon4.6
    Average homeowner rating
  • Verified reviews icon1k+
    Verified toilet services reviews

Find Toilet pros in Selma

Avatar for William Parrish Plumbing, Inc.
William Parrish Plumbing, Inc.
4.6(
258
)
Drain Clog or Blockage - Clear

Serving Selma, NC and surrounding areas

Approved

In business since 1965

Emergency services offered

Warranties offered

"Scott was the plumber that came to our house, he was very knowledgeable and replaced our pump within 2 hours. The clean up was done in no time at all and he was so professional. I would recommend this company if you are having plumbing issues."
 Serious water heater performance
 1000 gallon grease trap
Response time6 hrs
13 neighbors recently requested a quote
Recommended by97%of homeowners
C. Massey Plumbing
4.9(
36
)
Faucets, Fixtures and Pipes - Repair or Replace

Serving Selma, NC and surrounding areas

Approved

In business since 2008

Emergency services offered

Small jobs welcome

"Chris came out to replace my water heater. He was very professional and polite. The work was quality and the cost was about average to the area. He did the work fast and cleaned up any mess the job had left behind. Thank you!"
Response time40 mins
6 neighbors recently requested a quote
Recommended by96%of homeowners
...
Showing 1-10 of 154
Toilets questions, answered by experts

It is okay to use a drain auger on a toilet, just make sure you are using the correct tip size. The auger is a plumbing snake with a protective sleeve to protect the porcelain toilet bowl from getting scratched. Using too large of an auger can cause the snake to loop back and damage the inside of the drain and plumbing.

Toilets typically connect to your main vent stack, a vertical pipe that runs through all finished levels of your home and exits through the roof. It’s located behind the walls, but if you have an unfinished basement or a utility closet, you may find a portion of it running the vertical length of the space. Some basement toilets use an air admittance valve instead, which is a small vent located in the wall directly behind the toilet that extends upward a few feet from the drain.

You generally cannot replace a 10-inch rough-in toilet with a 12-inch model without making significant plumbing updates. A 12-inch rough-in toilet will not fit a 10-inch rough-in space because the floor drain is in the wrong position. To accommodate the larger toilet, you would need to move the drainpipe, which could cost between $0.75 and $30 per linear foot, plus labor. In most cases, it is more cost-effective and simpler to purchase a new 10-inch rough-in toilet. However, it is possible to install a 10-inch rough-in toilet in a 12-inch space by using a longer connector.

The amount of water wasted when a toilet ghost flushes depends on the cause of the ghost flushing. Leaky flapper valves tend to waste less water than a larger problem like a damaged flush valve that makes the toilet run constantly. Even if you don’t think you’re wasting a lot of water, it’s still a problem that should be fixed quickly. 

Yes, you should screw your flange to the subfloor, including cement. The best way to get this done is to predrill holes into the concrete using a hammer drill and a ¼-inch concrete bit. Be careful when you’re ready to bolt your flange down, as you can accidentally crack it. You can avoid this issue by not installing the screws too deep. Or, you can opt for a flange with a stainless steel ring so you don’t have to worry about cracking the plastic.

The Selma, NC homeowners’ guide to toilet services

From average costs to expert advice, get all the answers you need to get your job done.